Internet-Draft Editor: J. Sermersheim
Intended Category: Standard Track Novell, Inc
Document: draft-ietf-ldapbis-protocol-32.txt Oct 2005
Obsoletes: RFCs 2251, 2830, 3771
LDAP: The Protocol
Status of this Memo
By submitting this Internet-Draft, each
author represents that any applicable patent or other IPR claims of
which he or she is aware have been or will be disclosed, and any of
which he or she becomes aware will be disclosed, in accordance with
Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that other
groups may also distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress".
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire in February 2005.
Technical discussion of this document will take place on the IETF
LDAP Revision Working Group (LDAPbis) mailing list <ietf-
[email protected]>. Please send editorial comments directly to the
editor <[email protected]>.
Abstract
This document describes the protocol elements, along with their
semantics and encodings, of the Lightweight Directory Access Protocol
(LDAP). LDAP provides access to distributed directory services that
act in accordance with X.500 data and service models. These protocol
elements are based on those described in the X.500 Directory Access
Protocol (DAP).
Table of Contents
Sermersheim Internet-Draft - Expires April 2006 Page 1
Lightweight Directory Access Protocol Version 3
1. Introduction....................................................3
1.1. Relationship to Other LDAP Specifications.....................3
2. Conventions.....................................................3
3. Protocol Model..................................................4
3.1 Operation and LDAP Message Layer Relationship..................5
4. Elements of Protocol............................................5
4.1. Common Elements...............................................5
4.1.1. Message Envelope............................................5
4.1.2. String Types................................................7
4.1.3. Distinguished Name and Relative Distinguished Name..........7
4.1.4. Attribute Descriptions......................................8
4.1.5. Attribute Value.............................................8
4.1.6. Attribute Value Assertion...................................8
4.1.7. Attribute and PartialAttribute..............................9
4.1.8. Matching Rule Identifier....................................9
4.1.9. Result Message..............................................9
4.1.10. Referral..................................................11
4.1.11. Controls..................................................13
4.2. Bind Operation...............................................14
4.3. Unbind Operation.............................................17
4.4. Unsolicited Notification.....................................17
4.5. Search Operation.............................................18
4.6. Modify Operation.............................................29
4.7. Add Operation................................................31
4.8. Delete Operation.............................................31
4.9. Modify DN Operation..........................................32
4.10. Compare Operation...........................................33
4.11. Abandon Operation...........................................34
4.12. Extended Operation..........................................35
4.13. IntermediateResponse Message................................36
4.14. StartTLS Operation..........................................37
5. Protocol Encoding, Connection, and Transfer....................39
5.1. Protocol Encoding............................................39
5.2. Transmission Control Protocol (TCP)..........................40
5.3. Termination of the LDAP session..............................40
6. Security Considerations........................................40
7. Acknowledgements...............................................42
8. Normative References...........................................42
9. Informative References.........................................44
10. IANA Considerations...........................................44
11. Editor's Address..............................................45
Appendix A - LDAP Result Codes....................................46
A.1 Non-Error Result Codes........................................46
A.2 Result Codes..................................................46
Appendix B - Complete ASN.1 Definition............................51
Appendix C - Changes..............................................57
C.1 Changes made to RFC 2251:.....................................57
C.2 Changes made to RFC 2830:.....................................62
C.3 Changes made to RFC 3771:.....................................63
Sermersheim Internet-Draft - Expires April 2006 Page 2
Lightweight Directory Access Protocol Version 3
1. Introduction
The Directory is "a collection of open systems cooperating to provide
directory services" [X.500]. A directory user, which may be a human
or other entity, accesses the Directory through a client (or
Directory User Agent (DUA)). The client, on behalf of the directory
user, interacts with one or more servers (or Directory System Agents
(DSA)). Clients interact with servers using a directory access
protocol.
This document details the protocol elements of the Lightweight
Directory Access Protocol (LDAP), along with their semantics.
Following the description of protocol elements, it describes the way
in which the protocol elements are encoded and transferred.
1.1. Relationship to Other LDAP Specifications
This document is an integral part of the LDAP Technical Specification
[Roadmap] which obsoletes the previously defined LDAP technical
specification, RFC 3377, in its entirety.
This document, together with [Roadmap], [AuthMeth], and [Models],
obsoletes RFC 2251 in its entirety. Section 3.3 is obsoleted by
[Roadmap]. Sections 4.2.1 (portions), and 4.2.2 are obsoleted by
[AuthMeth]. Sections 3.2, 3.4, 4.1.3 (last paragraph), 4.1.4, 4.1.5,
4.1.5.1, 4.1.9 (last paragraph), 5.1, 6.1, and 6.2 (last paragraph)
are obsoleted by [Models]. The remainder of RFC 2251 is obsoleted by
this document. Appendix C.1 summarizes substantive changes in the
remainder.
This document obsoletes RFC 2830, Sections 2 and 4. The remainder of
RFC 2830 is obsoleted by [AuthMeth]. Appendix C.2 summarizes
substantive changes to the remaining sections.
This document also obsoletes RFC 3771 in entirety.
2. Conventions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", and "MAY" in this document are
to be interpreted as described in [Keyword].
Character names in this document use the notation for code points and
names from the Unicode Standard [Unicode]. For example, the letter
"a" may be represented as either <U+0061> or <LATIN SMALL LETTER A>.
Note: a glossary of terms used in Unicode can be found in [Glossary].
Information on the Unicode character encoding model can be found in
[CharModel].
Sermersheim Internet-Draft - Expires April 2006 Page 3
Lightweight Directory Access Protocol Version 3
The term "transport connection" refers to the underlying transport
services used to carry the protocol exchange, as well as associations
established by these services.
The term "TLS layer" refers to TLS services used in providing
security services, as well as associations established by these
services.
The term "SASL layer" refers to SASL services used in providing
security services, as well as associations established by these
services.
The term "LDAP message layer" refers to the LDAP Message Protocol
Data Unit (PDU) services used in providing directory services, as
well as associations established by these services.
The term "LDAP session" refers to combined services (transport
connection, TLS layer, SASL layer, LDAP message layer) and their
associations.
See the table in Section 5 for an illustration of these four terms.
3. Protocol Model
The general model adopted by this protocol is one of clients
performing protocol operations against servers. In this model, a
client transmits a protocol request describing the operation to be
performed to a server. The server is then responsible for performing
the necessary operation(s) in the Directory. Upon completion of an
operation, the server typically returns a response containing
appropriate data to the requesting client.
Protocol operations are generally independent of one another. Each
operation is processed as an atomic action, leaving the directory in
a consistent state.
Although servers are required to return responses whenever such
responses are defined in the protocol, there is no requirement for
synchronous behavior on the part of either clients or servers.
Requests and responses for multiple operations generally may be
exchanged between a client and server in any order. If required,
synchronous behavior may be controlled by client applications.
The core protocol operations defined in this document can be mapped
to a subset of the X.500 (1993) Directory Abstract Service [X.511].
However there is not a one-to-one mapping between LDAP operations and
X.500 Directory Access Protocol (DAP) operations. Server
implementations acting as a gateway to X.500 directories may need to
make multiple DAP requests to service a single LDAP request.
Sermersheim Internet-Draft - Expires April 2006 Page 4
Lightweight Directory Access Protocol Version 3
3.1. Operation and LDAP Message Layer Relationship
Protocol operations are exchanged at the LDAP message layer. When the
transport connection is closed, any uncompleted operations at the
LDAP message layer, when possible, are abandoned, and when not
possible, are completed without transmission of the response. Also,
when the transport connection is closed, the client MUST NOT assume
that any uncompleted update operations have succeeded or failed.
4. Elements of Protocol
The protocol is described using Abstract Syntax Notation One
([ASN.1]), and is transferred using a subset of ASN.1 Basic Encoding
Rules ([BER]). Section 5 specifies how the protocol elements are
encoded and transferred.
In order to support future extensions to this protocol, extensibility
is implied where it is allowed per ASN.1 (i.e. sequence, set, choice,
and enumerated types are extensible). In addition, ellipses (...)
have been supplied in ASN.1 types that are explicitly extensible as
discussed in [LDAPIANA]. Because of the implied extensibility,
clients and servers MUST (unless otherwise specified) ignore trailing
SEQUENCE components whose tags they do not recognize.
Changes to the protocol other than through the extension mechanisms
described here require a different version number. A client indicates
the version it is using as part of the BindRequest, described in
Section 4.2. If a client has not sent a Bind, the server MUST assume
the client is using version 3 or later.
Clients may attempt to determine the protocol versions a server
supports by reading the 'supportedLDAPVersion' attribute from the
root DSE (DSA-Specific Entry) [Models].
4.1. Common Elements
This section describes the LDAPMessage envelope Protocol Data Unit
(PDU) format, as well as data type definitions, which are used in the
protocol operations.
4.1.1. Message Envelope
For the purposes of protocol exchanges, all protocol operations are
encapsulated in a common envelope, the LDAPMessage, which is defined
as follows:
Sermersheim Internet-Draft - Expires April 2006 Page 5
Lightweight Directory Access Protocol Version 3
LDAPMessage ::= SEQUENCE {
messageID MessageID,
protocolOp CHOICE {
bindRequest BindRequest,
bindResponse BindResponse,
unbindRequest UnbindRequest,
searchRequest SearchRequest,
searchResEntry SearchResultEntry,
searchResDone SearchResultDone,
searchResRef SearchResultReference,
modifyRequest ModifyRequest,
modifyResponse ModifyResponse,
addRequest AddRequest,
addResponse AddResponse,
delRequest DelRequest,
delResponse DelResponse,
modDNRequest ModifyDNRequest,
modDNResponse ModifyDNResponse,
compareRequest CompareRequest,
compareResponse CompareResponse,
abandonRequest AbandonRequest,
extendedReq ExtendedRequest,
extendedResp ExtendedResponse,
...,
intermediateResponse IntermediateResponse },
controls [0] Controls OPTIONAL }
MessageID ::= INTEGER (0 .. maxInt)
maxInt INTEGER ::= 2147483647 -- (2^^31 - 1) --
The ASN.1 type Controls is defined in Section 4.1.11.
The function of the LDAPMessage is to provide an envelope containing
common fields required in all protocol exchanges. At this time the
only common fields are the messageID and the controls.
If the server receives an LDAPMessage from the client in which the
LDAPMessage SEQUENCE tag cannot be recognized, the messageID cannot
be parsed, the tag of the protocolOp is not recognized as a request,
or the encoding structures or lengths of data fields are found to be
incorrect, then the server SHOULD return the Notice of Disconnection
described in Section 4.4.1, with the resultCode set to protocolError,
and MUST immediately terminate the LDAP session as described in
Section 5.3.
In other cases where the client or server cannot parse an LDAP PDU,
it SHOULD abruptly terminate the LDAP session (Section 5.3) where
further communication (including providing notice) would be
pernicious. Otherwise, server implementations MUST return an
appropriate response to the request, with the resultCode set to
protocolError.
Sermersheim Internet-Draft - Expires April 2006 Page 6
Lightweight Directory Access Protocol Version 3
4.1.1.1. Message ID
All LDAPMessage envelopes encapsulating responses contain the
messageID value of the corresponding request LDAPMessage.
The message ID of a request MUST have a non-zero value different from
the messageID of any other request in progress in the same LDAP
session. The zero value is reserved for the unsolicited notification
message.
Typical clients increment a counter for each request.
A client MUST NOT send a request with the same message ID as an
earlier request in the same LDAP session unless it can be determined
that the server is no longer servicing the earlier request (e.g.
after the final response is received, or a subsequent Bind
completes). Otherwise the behavior is undefined. For this purpose,
note that Abandon and successfully abandoned operations do not send
responses.
4.1.2. String Types
The LDAPString is a notational convenience to indicate that, although
strings of LDAPString type encode as ASN.1 OCTET STRING types, the
[ISO10646] character set (a superset of [Unicode]) is used, encoded
following the [UTF-8] algorithm. Note that Unicode characters U+0000
through U+007F are the same as ASCII 0 through 127, respectively, and
have the same single octet UTF-8 encoding. Other Unicode characters
have a multiple octet UTF-8 encoding.
LDAPString ::= OCTET STRING -- UTF-8 encoded,
-- [ISO10646] characters
The LDAPOID is a notational convenience to indicate that the
permitted value of this string is a (UTF-8 encoded) dotted-decimal
representation of an OBJECT IDENTIFIER. Although an LDAPOID is
encoded as an OCTET STRING, values are limited to the definition of
<numericoid> given in Section 1.4 of [Models].
LDAPOID ::= OCTET STRING -- Constrained to <numericoid> [Models]
For example,
1.3.6.1.4.1.1466.1.2.3
4.1.3. Distinguished Name and Relative Distinguished Name
An LDAPDN is defined to be the representation of a Distinguished Name
(DN) after encoding according to the specification in [LDAPDN].
LDAPDN ::= LDAPString
-- Constrained to <distinguishedName> [LDAPDN]
Sermersheim Internet-Draft - Expires April 2006 Page 7
Lightweight Directory Access Protocol Version 3
A RelativeLDAPDN is defined to be the representation of a Relative
Distinguished Name (RDN) after encoding according to the
specification in [LDAPDN].
RelativeLDAPDN ::= LDAPString
-- Constrained to <name-component> [LDAPDN]
4.1.4. Attribute Descriptions
The definition and encoding rules for attribute descriptions are
defined in Section 2.5 of [Models]. Briefly, an attribute description
is an attribute type and zero or more options.
AttributeDescription ::= LDAPString
-- Constrained to <attributedescription>
-- [Models]
4.1.5. Attribute Value
A field of type AttributeValue is an OCTET STRING containing an
encoded attribute value. The attribute value is encoded according to
the LDAP-specific encoding definition of its corresponding syntax.
The LDAP-specific encoding definitions for different syntaxes and
attribute types may be found in other documents and in particular
[Syntaxes].
AttributeValue ::= OCTET STRING
Note that there is no defined limit on the size of this encoding;
thus protocol values may include multi-megabyte attribute values
(e.g. photographs).
Attribute values may be defined which have arbitrary and non-
printable syntax. Implementations MUST NOT display nor attempt to
decode an attribute value if its syntax is not known. The
implementation may attempt to discover the subschema of the source
entry, and retrieve the descriptions of 'attributeTypes' from it
[Models].
Clients MUST only send attribute values in a request that are valid
according to the syntax defined for the attributes.
4.1.6. Attribute Value Assertion
The AttributeValueAssertion (AVA) type definition is similar to the
one in the X.500 Directory standards. It contains an attribute
description and a matching rule ([Models] Section 4.1.3) assertion
value suitable for that type. Elements of this type are typically
used to assert that the value in assertionValue matches a value of an
attribute.
Sermersheim Internet-Draft - Expires April 2006 Page 8
Lightweight Directory Access Protocol Version 3
AttributeValueAssertion ::= SEQUENCE {
attributeDesc AttributeDescription,
assertionValue AssertionValue }
AssertionValue ::= OCTET STRING
The syntax of the AssertionValue depends on the context of the LDAP
operation being performed. For example, the syntax of the EQUALITY
matching rule for an attribute is used when performing a Compare
operation. Often this is the same syntax used for values of the
attribute type, but in some cases the assertion syntax differs from
the value syntax. See objectIdentiferFirstComponentMatch in
[Syntaxes] for an example.
4.1.7. Attribute and PartialAttribute
Attributes and partial attributes consist of an attribute description
and attribute values. A PartialAttribute allows zero values, while
Attribute requires at least one value.
PartialAttribute ::= SEQUENCE {
type AttributeDescription,
vals SET OF value AttributeValue }
Attribute ::= PartialAttribute(WITH COMPONENTS {
...,
vals (SIZE(1..MAX))})
No two of the attribute values may be equivalent as described by
Section 2.3 of [Models]. The set of attribute values is unordered.
Implementations MUST NOT rely upon the ordering being repeatable.
4.1.8. Matching Rule Identifier
Matching rules are defined in Section 4.1.3 of [Models]. A matching
rule is identified in the protocol by the printable representation of
either its <numericoid>, or one of its short name descriptors
[Models], e.g. 'caseIgnoreMatch' or '2.5.13.2'.
MatchingRuleId ::= LDAPString
4.1.9. Result Message
The LDAPResult is the construct used in this protocol to return
success or failure indications from servers to clients. To various
requests, servers will return responses containing the elements found
in LDAPResult to indicate the final status of the protocol operation
request.
Sermersheim Internet-Draft - Expires April 2006 Page 9
Lightweight Directory Access Protocol Version 3
LDAPResult ::= SEQUENCE {
resultCode ENUMERATED {
success (0),
operationsError (1),
protocolError (2),
timeLimitExceeded (3),
sizeLimitExceeded (4),
compareFalse (5),
compareTrue (6),
authMethodNotSupported (7),
strongerAuthRequired (8),
-- 9 reserved --
referral (10),
adminLimitExceeded (11),
unavailableCriticalExtension (12),
confidentialityRequired (13),
saslBindInProgress (14),
noSuchAttribute (16),
undefinedAttributeType (17),
inappropriateMatching (18),
constraintViolation (19),
attributeOrValueExists (20),
invalidAttributeSyntax (21),
-- 22-31 unused --
noSuchObject (32),
aliasProblem (33),
invalidDNSyntax (34),
-- 35 reserved for undefined isLeaf --
aliasDereferencingProblem (36),
-- 37-47 unused --
inappropriateAuthentication (48),
invalidCredentials (49),
insufficientAccessRights (50),
busy (51),
unavailable (52),
unwillingToPerform (53),
loopDetect (54),
-- 55-63 unused --
namingViolation (64),
objectClassViolation (65),
notAllowedOnNonLeaf (66),
notAllowedOnRDN (67),
entryAlreadyExists (68),
objectClassModsProhibited (69),
-- 70 reserved for CLDAP --
affectsMultipleDSAs (71),
-- 72-79 unused --
other (80),
... },
matchedDN LDAPDN,
diagnosticMessage LDAPString,
referral [3] Referral OPTIONAL }
Sermersheim Internet-Draft - Expires April 2006 Page 10
Lightweight Directory Access Protocol Version 3
The resultCode enumeration is extensible as defined in Section 3.6 of
[LDAPIANA]. The meanings of the listed result codes are given in
Appendix A. If a server detects multiple errors for an operation,
only one result code is returned. The server should return the result
code that best indicates the nature of the error encountered. Servers
may return substituted result codes to prevent unauthorized
disclosures.
The diagnosticMessage field of this construct may, at the server's
option, be used to return a string containing a textual, human-
readable (terminal control and page formatting characters should be
avoided) diagnostic message. As this diagnostic message is not
standardized, implementations MUST NOT rely on the values returned.
Diagnostic messages typically supplement the resultCode with
additional information. If the server chooses not to return a textual
diagnostic, the diagnosticMessage field MUST be empty.
For certain result codes (typically, but not restricted to
noSuchObject, aliasProblem, invalidDNSyntax and
aliasDereferencingProblem), the matchedDN field is set (subject to
access controls) to the name of the last entry (object or alias) used
in finding the target (or base) object. This will be a truncated form
of the provided name or, if an alias was dereferenced while
attempting to locate the entry, of the resulting name. Otherwise the
matchedDN field is empty.
4.1.10. Referral
The referral result code indicates that the contacted server cannot
or will not perform the operation and that one or more other servers
may be able to. Reasons for this include:
- The target entry of the request is not held locally, but the
server has knowledge of its possible existence elsewhere.
- The operation is restricted on this server -- perhaps due to a
read-only copy of an entry to be modified.
The referral field is present in an LDAPResult if the resultCode is
set to referral, and absent with all other result codes. It contains
one or more references to one or more servers or services that may be
accessed via LDAP or other protocols. Referrals can be returned in
response to any operation request (except Unbind and Abandon which do
not have responses). At least one URI MUST be present in the
Referral.
During a Search operation, after the baseObject is located, and
entries are being evaluated, the referral is not returned. Instead,
continuation references, described in Section 4.5.3, are returned
when other servers would need to be contacted to complete the
operation.
Referral ::= SEQUENCE SIZE (1..MAX) OF uri URI
Sermersheim Internet-Draft - Expires April 2006 Page 11
Lightweight Directory Access Protocol Version 3
URI ::= LDAPString -- limited to characters permitted in
-- URIs
If the client wishes to progress the operation, it contacts one of
the supported services found in the referral. If multiple URIs are
present, the client assumes that any supported URI may be used to
progress the operation.
Clients that follow referrals MUST ensure that they do not loop
between servers. They MUST NOT repeatedly contact the same server for
the same request with the same parameters. Some clients use a counter
that is incremented each time referral handling occurs for an
operation, and these kinds of clients MUST be able to handle at least
ten nested referrals while progressing the operation.
A URI for a server implementing LDAP and accessible via [TCP]/[IP]
(v4 or v6) is written as an LDAP URL according to [LDAPURL].
Referral values which are LDAP URLs follow these rules:
- If an alias was dereferenced, the <dn> part of the LDAP URL MUST
be present, with the new target object name.
- It is RECOMMENDED that the <dn> part be present to avoid
ambiguity.
- If the <dn> part is present, the client uses this name in its next
request to progress the operation, and if it is not present the
client uses the same name as in the original request.
- Some servers (e.g. participating in distributed indexing) may
provide a different filter in a URL of a referral for a Search
operation.
- If the <filter> part of the LDAP URL is present, the client uses
this filter in its next request to progress this Search, and if it
is not present the client uses the same filter as it used for that
Search.
- For Search, it is RECOMMENDED that the <scope> part be present to
avoid ambiguity.
- If the <scope> part is missing, the scope of the original Search
is used by the client to progress the operation.
- Other aspects of the new request may be the same as or different
from the request which generated the referral.
Other kinds of URIs may be returned. The syntax and semantics of such
URIs is left to future specifications. Clients may ignore URIs that
they do not support.
Sermersheim Internet-Draft - Expires April 2006 Page 12
Lightweight Directory Access Protocol Version 3
UTF-8 encoded characters appearing in the string representation of a
DN, search filter, or other fields of the referral value may not be
legal for URIs (e.g. spaces) and MUST be escaped using the % method
in [URI].
4.1.11. Controls
Controls provide a mechanism whereby the semantics and arguments of
existing LDAP operations may be extended. One or more controls may be
attached to a single LDAP message. A control only affects the
semantics of the message it is attached to.
Controls sent by clients are termed 'request controls' and those sent
by servers are termed 'response controls'.
Controls ::= SEQUENCE OF control Control
Control ::= SEQUENCE {
controlType LDAPOID,
criticality BOOLEAN DEFAULT FALSE,
controlValue OCTET STRING OPTIONAL }
The controlType field is the dotted-decimal representation of an
OBJECT IDENTIFIER which uniquely identifies the control. This
provides unambiguous naming of controls. Often, response control(s)
solicited by a request control share controlType values with the
request control.
The criticality field only has meaning in controls attached to
request messages (except UnbindRequest). For controls attached to
response messages and the UnbindRequest, the criticality field SHOULD
be FALSE, and MUST be ignored by the receiving protocol peer. A value
of TRUE indicates that it is unacceptable to perform the operation
without applying the semantics of the control. Specifically, the
criticality field is applied as follows:
- If the server does not recognize the control type, determines that
it is not appropriate for the operation, or is otherwise unwilling
to perform the operation with the control, and the criticality
field is TRUE, the server MUST NOT perform the operation, and for
operations that have a response message, MUST return with the
resultCode set to unavailableCriticalExtension.
- If the server does not recognize the control type, determines that
it is not appropriate for the operation, or is otherwise unwilling
to perform the operation with the control, and the criticality
field is FALSE, the server MUST ignore the control.
- Regardless of criticality, if a control is applied to an
operation, it is applied consistently and impartially to the
entire operation.
Sermersheim Internet-Draft - Expires April 2006 Page 13
Lightweight Directory Access Protocol Version 3
The controlValue may contain information associated with the
controlType. Its format is defined by the specification of the
control. Implementations MUST be prepared to handle arbitrary
contents of the controlValue octet string, including zero bytes. It
is absent only if there is no value information which is associated
with a control of its type. When a controlValue is defined in terms
of ASN.1, and BER encoded according to Section 5.1, it also follows
the extensibility rules in Section 4.
Servers list the controlType of request controls they recognize in
the 'supportedControl' attribute in the root DSE (Section 5.1 of
[Models]).
Controls SHOULD NOT be combined unless the semantics of the
combination has been specified. The semantics of control
combinations, if specified, are generally found in the control
specification most recently published. When a combination of controls
is encountered whose semantics are invalid, not specified (or not
known), the message is considered to be not well-formed, thus the
operation fails with protocolError. Controls with a criticality of
FALSE may be ignored in order to arrive at a valid combination.
Additionally, unless order-dependent semantics are given in a
specification, the order of a combination of controls in the SEQUENCE
is ignored. Where the order is to be ignored but cannot be ignored by
the server, the message is considered not well-formed and the
operation fails with protocolError. Again, controls with a
criticality of FALSE may be ignored in order to arrive at a valid
combination.
This document does not specify any controls. Controls may be
specified in other documents. Documents detailing control extensions
are to provide for each control:
- the OBJECT IDENTIFIER assigned to the control,
- direction as to what value the sender should provide for the
criticality field (note: the semantics of the criticality field
are defined above should not be altered by the control's
specification),
- whether the controlValue field is present, and if so, the format
of its contents,
- the semantics of the control, and
- optionally, semantics regarding the combination of the control
with other controls.
4.2. Bind Operation
Sermersheim Internet-Draft - Expires April 2006 Page 14
Lightweight Directory Access Protocol Version 3
The function of the Bind operation is to allow authentication
information to be exchanged between the client and server. The Bind
operation should be thought of as the "authenticate" operation.
Operational, authentication, and security-related semantics of this
operation are given in [AuthMeth].
The Bind request is defined as follows:
BindRequest ::= [APPLICATION 0] SEQUENCE {
version INTEGER (1 .. 127),
name LDAPDN,
authentication AuthenticationChoice }
AuthenticationChoice ::= CHOICE {
simple [0] OCTET STRING,
-- 1 and 2 reserved
sasl [3] SaslCredentials,
... }
SaslCredentials ::= SEQUENCE {
mechanism LDAPString,
credentials OCTET STRING OPTIONAL }
Fields of the BindRequest are:
- version: A version number indicating the version of the protocol
to be used at the LDAP message layer. This document describes
version 3 of the protocol. There is no version negotiation. The
client sets this field to the version it desires. If the server
does not support the specified version, it MUST respond with a
BindResponse where the resultCode is set to protocolError.
- name: If not empty, the name of the Directory object that the
client wishes to bind as. This field may take on a null value (a
zero length string) for the purposes of anonymous binds
([AuthMeth] Section 5.1) or when using Simple Authentication and
Security Layer [SASL] authentication ([AuthMeth] Section 5.2).
Where the server attempts to locate the named object, it SHALL NOT
perform alias dereferencing.
- authentication: information used in authentication. This type is
extensible as defined in Section 3.7 of [LDAPIANA]. Servers that
do not support a choice supplied by a client return a BindResponse
with the resultCode set to authMethodNotSupported.
Textual passwords (consisting of a character sequence with a known
character set and encoding) transferred to the server using the
simple AuthenticationChoice SHALL be transferred as [UTF-8]
encoded [Unicode]. Prior to transfer, clients SHOULD prepare text
passwords as "query" strings by applying the [SASLprep] profile of
the [Stringprep] algorithm. Passwords consisting of other data
(such as random octets) MUST NOT be altered. The determination of
whether a password is textual is a local client matter.
Sermersheim Internet-Draft - Expires April 2006 Page 15
Lightweight Directory Access Protocol Version 3
4.2.1. Processing of the Bind Request
Before processing a BindRequest, all uncompleted operations MUST
either complete or be abandoned. The server may either wait for the
uncompleted operations to complete, or abandon them. The server then
proceeds to authenticate the client in either a single-step, or
multi-step Bind process. Each step requires the server to return a
BindResponse to indicate the status of authentication.
After sending a BindRequest, clients MUST NOT send further LDAP PDUs
until receiving the BindResponse. Similarly, servers SHOULD NOT
process or respond to requests received while processing a
BindRequest.
If the client did not bind before sending a request and receives an
operationsError to that request, it may then send a BindRequest. If
this also fails or the client chooses not to bind on the existing
LDAP session, it may terminate the LDAP session, re-establish it and
begin again by first sending a BindRequest. This will aid in
interoperating with servers implementing other versions of LDAP.
Clients may send multiple Bind requests to change the authentication
and/or security associations or to complete a multi-stage Bind
process. Authentication from earlier binds is subsequently ignored.
For some SASL authentication mechanisms, it may be necessary for the
client to invoke the BindRequest multiple times ([AuthMeth] Section
5.2). Clients MUST NOT invoke operations between two Bind requests
made as part of a multi-stage Bind.
A client may abort a SASL bind negotiation by sending a BindRequest
with a different value in the mechanism field of SaslCredentials, or
an AuthenticationChoice other than sasl.
If the client sends a BindRequest with the sasl mechanism field as an
empty string, the server MUST return a BindResponse with the
resultCode set to authMethodNotSupported. This will allow clients to
abort a negotiation if it wishes to try again with the same SASL
mechanism.
4.2.2. Bind Response
The Bind response is defined as follows.
BindResponse ::= [APPLICATION 1] SEQUENCE {
COMPONENTS OF LDAPResult,
serverSaslCreds [7] OCTET STRING OPTIONAL }
BindResponse consists simply of an indication from the server of the
status of the client's request for authentication.
Sermersheim Internet-Draft - Expires April 2006 Page 16
Lightweight Directory Access Protocol Version 3
A successful Bind operation is indicated by a BindResponse with a
resultCode set to success. Otherwise, an appropriate result code is
set in the BindResponse. For BindResponse, the protocolError result
code may be used to indicate that the version number supplied by the
client is unsupported.
If the client receives a BindResponse where the resultCode is set to
protocolError, it is to assume that the server does not support this
version of LDAP. While the client may be able proceed with another
version of this protocol (this may or may not require closing and re-
establishing the transport connection), how to proceed with another
version of this protocol is beyond the scope of this document.
Clients which are unable or unwilling to proceed SHOULD terminate the
LDAP session.
The serverSaslCreds field is used as part of a SASL-defined bind
mechanism to allow the client to authenticate the server to which it
is communicating, or to perform "challenge-response" authentication.
If the client bound with the simple choice, or the SASL mechanism
does not require the server to return information to the client, then
this field SHALL NOT be included in the BindResponse.
4.3. Unbind Operation
The function of the Unbind operation is to terminate an LDAP session.
The Unbind operation is not the antithesis of the Bind operation as
the name implies. The naming of these operations are historical. The
Unbind operation should be thought of as the "quit" operation.
The Unbind operation is defined as follows:
UnbindRequest ::= [APPLICATION 2] NULL
The client, upon transmission of the UnbindRequest, and the server,
upon receipt of the UnbindRequest are to gracefully terminate the
LDAP session as described in Section 5.3.
Uncompleted operations are handled as specified in Section 3.1.
4.4. Unsolicited Notification
An unsolicited notification is an LDAPMessage sent from the server to
the client which is not in response to any LDAPMessage received by
the server. It is used to signal an extraordinary condition in the
server or in the LDAP session between the client and the server. The
notification is of an advisory nature, and the server will not expect
any response to be returned from the client.
Sermersheim Internet-Draft - Expires April 2006 Page 17
Lightweight Directory Access Protocol Version 3
The unsolicited notification is structured as an LDAPMessage in which
the messageID is zero and protocolOp is set to the extendedResp
choice using the ExtendedResponse type (See Section 4.12). The
responseName field of the ExtendedResponse always contains an LDAPOID
which is unique for this notification.
One unsolicited notification (Notice of Disconnection) is defined in
this document. The specification of an unsolicited notification
consists of:
- the OBJECT IDENTIFIER assigned to the notification (to be
specified in the responseName,
- the format of the contents of the responseValue (if any),
- the circumstances which will cause the notification to be sent,
and
- the semantics of the message.
4.4.1. Notice of Disconnection
This notification may be used by the server to advise the client that
the server is about to terminate the LDAP session on its own
initiative. This notification is intended to assist clients in
distinguishing between an exceptional server condition and a
transient network failure. Note that this notification is not a
response to an Unbind requested by the client. Uncompleted operations
are handled as specified in Section 3.1.
The responseName is 1.3.6.1.4.1.1466.20036, the responseValue field
is absent, and the resultCode is used to indicate the reason for the
disconnection. When the strongerAuthRequired resultCode is returned
with this message, it indicates that the server has detected that an
established security association between the client and server has
unexpectedly failed or been compromised.
Upon transmission of the Notice of Disconnection, the server
gracefully terminates the LDAP session as described in Section 5.3.
4.5. Search Operation
The Search operation is used to request a server to return, subject
to access controls and other restrictions, a set of entries matching
a complex search criterion. This can be used to read attributes from
a single entry, from entries immediately subordinate to a particular
entry, or a whole subtree of entries.
4.5.1. Search Request
The Search request is defined as follows:
Sermersheim Internet-Draft - Expires April 2006 Page 18
Lightweight Directory Access Protocol Version 3
SearchRequest ::= [APPLICATION 3] SEQUENCE {
baseObject LDAPDN,
scope ENUMERATED {
baseObject (0),
singleLevel (1),
wholeSubtree (2),
... },
derefAliases ENUMERATED {
neverDerefAliases (0),
derefInSearching (1),
derefFindingBaseObj (2),
derefAlways (3) },
sizeLimit INTEGER (0 .. maxInt),
timeLimit INTEGER (0 .. maxInt),
typesOnly BOOLEAN,
filter Filter,
attributes AttributeSelection }
AttributeSelection ::= SEQUENCE OF selector LDAPString
-- The LDAPString is constrained to
-- <attributeSelector> in Section 4.5.1.7
Filter ::= CHOICE {
and [0] SET SIZE (1..MAX) OF filter Filter,
or [1] SET SIZE (1..MAX) OF filter Filter,
not [2] Filter,
equalityMatch [3] AttributeValueAssertion,
substrings [4] SubstringFilter,
greaterOrEqual [5] AttributeValueAssertion,
lessOrEqual [6] AttributeValueAssertion,
present [7] AttributeDescription,
approxMatch [8] AttributeValueAssertion,
extensibleMatch [9] MatchingRuleAssertion,
... }
SubstringFilter ::= SEQUENCE {
type AttributeDescription,
substrings SEQUENCE SIZE (1..MAX) OF substring CHOICE {
initial [0] AssertionValue, -- can occur at most once
any [1] AssertionValue,
final [2] AssertionValue } -- can occur at most once
}
MatchingRuleAssertion ::= SEQUENCE {
matchingRule [1] MatchingRuleId OPTIONAL,
type [2] AttributeDescription OPTIONAL,
matchValue [3] AssertionValue,
dnAttributes [4] BOOLEAN DEFAULT FALSE }
Sermersheim Internet-Draft - Expires April 2006 Page 19
Lightweight Directory Access Protocol Version 3
Note that an X.500 "list"-like operation can be emulated by the
client requesting a singleLevel Search operation with a filter
checking for the presence of the 'objectClass' attribute, and that an
X.500 "read"-like operation can be emulated by a baseObject Search
operation with the same filter. A server which provides a gateway to
X.500 is not required to use the Read or List operations, although it
may choose to do so, and if it does, it must provide the same
semantics as the X.500 Search operation.
4.5.1.1. SearchRequest.baseObject
The name of the base object entry (or possibly the root) relative to
which the Search is to be performed.
4.5.1.2. SearchRequest.scope
Specifies the scope of the Search to be performed. The semantics (as
described in [X.511]) of the defined values of this field are:
baseObject: The scope is constrained to the entry named by
baseObject.
singleLevel: The scope is constrained to the immediate
subordinates of the entry named by baseObject.
wholeSubtree: the scope is constrained to the entry named by the
baseObject, and all its subordinates.
4.5.1.3. SearchRequest.derefAliases
An indicator as to whether or not alias entries (as defined in
[Models]) are to be dereferenced during stages of the Search
operation.
The act of dereferencing an alias includes recursively dereferencing
aliases which refer to aliases.
Servers MUST detect looping while dereferencing aliases in order to
prevent denial of service attacks of this nature.
The semantics of the defined values of this field are:
neverDerefAliases: Do not dereference aliases in searching or in
locating the base object of the Search.
Sermersheim Internet-Draft - Expires April 2006 Page 20
Lightweight Directory Access Protocol Version 3
derefInSearching: While searching subordinates of the base object,
dereference any alias within the search scope. Dereferenced
objects become the vertices of further search scopes where the
Search operation is also applied. If the search scope is
wholeSubtree, the Search continues in the subtree(s) of any
dereferenced object. If the search scope is singleLevel, the
search is applied to any dereferenced objects, and is not applied
to their subordinates. Servers SHOULD eliminate duplicate entries
that arise due to alias dereferencing while searching.
derefFindingBaseObj: Dereference aliases in locating the base
object of the Search, but not when searching subordinates of the
base object.
derefAlways: Dereference aliases both in searching and in locating
the base object of the Search.
4.5.1.4. SearchRequest.sizeLimit
A size limit that restricts the maximum number of entries to be
returned as a result of the Search. A value of zero in this field
indicates that no client-requested size limit restrictions are in
effect for the Search. Servers may also enforce a maximum number of
entries to return.
4.5.1.5. SearchRequest.timeLimit
A time limit that restricts the maximum time (in seconds) allowed for
a Search. A value of zero in this field indicates that no client-
requested time limit restrictions are in effect for the Search.
Servers may also enforce a maximum time limit for the Search.
4.5.1.6. SearchRequest.typesOnly
An indicator as to whether Search results are to contain both
attribute descriptions and values, or just attribute descriptions.
Setting this field to TRUE causes only attribute descriptions (no
values) to be returned. Setting this field to FALSE causes both
attribute descriptions and values to be returned.
Sermersheim Internet-Draft - Expires April 2006 Page 21
Lightweight Directory Access Protocol Version 3
4.5.1.7. SearchRequest.filter
A filter that defines the conditions that must be fulfilled in order
for the Search to match a given entry.
The 'and', 'or' and 'not' choices can be used to form combinations of
filters. At least one filter element MUST be present in an 'and' or
'or' choice. The others match against individual attribute values of
entries in the scope of the Search. (Implementor's note: the 'not'
filter is an example of a tagged choice in an implicitly-tagged
module. In BER this is treated as if the tag was explicit.)
A server MUST evaluate filters according to the three-valued logic of
[X.511] (1993) Clause 7.8.1. In summary, a filter is evaluated to
either "TRUE", "FALSE" or "Undefined". If the filter evaluates to
TRUE for a particular entry, then the attributes of that entry are
returned as part of the Search result (subject to any applicable
access control restrictions). If the filter evaluates to FALSE or
Undefined, then the entry is ignored for the Search.
A filter of the "and" choice is TRUE if all the filters in the SET OF
evaluate to TRUE, FALSE if at least one filter is FALSE, and
otherwise Undefined. A filter of the "or" choice is FALSE if all of
the filters in the SET OF evaluate to FALSE, TRUE if at least one
filter is TRUE, and Undefined otherwise. A filter of the 'not' choice
is TRUE if the filter being negated is FALSE, FALSE if it is TRUE,
and Undefined if it is Undefined.
A filter item evaluates to Undefined when the server would not be
able to determine whether the assertion value matches an entry.
Examples include:
- An attribute description in an equalityMatch, substrings,
greaterOrEqual, lessOrEqual, approxMatch or extensibleMatch
filter is not recognized by the server.
- The attribute type does not define the appropriate matching
rule.
- A MatchingRuleId in the extensibleMatch is not recognized by
the server or is not valid for the attribute type.
- The type of filtering requested is not implemented.
- The assertion value is invalid.
For example, if a server did not recognize the attribute type
shoeSize, the filters (shoeSize=*), (shoeSize=12), (shoeSize>=12) and
(shoeSize<=12) would each evaluate to Undefined.
Servers MUST NOT return errors if attribute descriptions or matching
rule ids are not recognized, assertion values are invalid, or the
assertion syntax is not supported. More details of filter processing
are given in Clause 7.8 of [X.511].
Sermersheim Internet-Draft - Expires April 2006 Page 22
Lightweight Directory Access Protocol Version 3
4.5.1.7.1. SearchRequest.filter.equalityMatch
The matching rule for an equalityMatch filter is defined by the
EQUALITY matching rule for the attribute type or subtype. The filter
is TRUE when the EQUALITY rule returns TRUE as applied to the
attribute or subtype and the asserted value.
4.5.1.7.2. SearchRequest.filter.substrings
There SHALL be at most one 'initial', and at most one 'final' in the
'substrings' of a SubstringFilter. If 'initial' is present, it SHALL
be the first element of 'substrings'. If 'final' is present, it SHALL
be the last element of 'substrings'.
The matching rule for an AssertionValue in a substrings filter item
is defined by the SUBSTR matching rule for the attribute type or
subtype. The filter is TRUE when the SUBSTR rule returns TRUE as
applied to the attribute or subtype and the asserted value.
Note that the AssertionValue in a substrings filter item conforms to
the assertion syntax of the EQUALITY matching rule for the attribute
type rather than the assertion syntax of the SUBSTR matching rule for
the attribute type. Conceptually, the entire SubstringFilter is
converted into an assertion value of the substrings matching rule
prior to applying the rule.
4.5.1.7.3. SearchRequest.filter.greaterOrEqual
The matching rule for a greaterOrEqual filter is defined by the
ORDERING matching rule for the attribute type or subtype. The filter
is TRUE when the ORDERING rule returns FALSE as applied to the
attribute or subtype and the asserted value.
4.5.1.7.4. SearchRequest.filter.lessOrEqual
The matching rules for a lessOrEqual filter are defined by the
ORDERING and EQUALITY matching rules for the attribute type or
subtype. The filter is TRUE when either the ORDERING or EQUALITY rule
returns TRUE as applied to the attribute or subtype and the asserted
value.
4.5.1.7.5. SearchRequest.filter.present
A present filter is TRUE when there is an attribute or subtype of the
specified attribute description present in an entry, FALSE when no
attribute or subtype of the specified attribute description is
present in an entry, and Undefined otherwise.
Sermersheim Internet-Draft - Expires April 2006 Page 23
Lightweight Directory Access Protocol Version 3
4.5.1.7.6. SearchRequest.filter.approxMatch
An approxMatch filter is TRUE when there is a value of the attribute
type or subtype for which some locally-defined approximate matching
algorithm (e.g. spelling variations, phonetic match, etc.) returns
TRUE. If a value matches for equality, it also satisfies an
approximate match. If approximate matching is not supported for the
attribute, this filter item should be treated as an equalityMatch.
4.5.1.7.7. SearchRequest.filter.extensibleMatch
The fields of the extensibleMatch filter item are evaluated as
follows:
- If the matchingRule field is absent, the type field MUST be
present, and an equality match is performed for that type.
- If the type field is absent and the matchingRule is present, the
matchValue is compared against all attributes in an entry which
support that matchingRule.
- If the type field is present and the matchingRule is present, the
matchValue is compared against the specified attribute type and
its subtypes.
- If the dnAttributes field is set to TRUE, the match is
additionally applied against all the AttributeValueAssertions in
an entry's distinguished name, and evaluates to TRUE if there is
at least one attribute or subtype in the distinguished name for
which the filter item evaluates to TRUE. The dnAttributes field is
present to alleviate the need for multiple versions of generic
matching rules (such as word matching), where one applies to
entries and another applies to entries and DN attributes as well.
The matchingRule used for evaluation determines the syntax for the
assertion value. Once the matchingRule and attribute(s) have been
determined, the filter item evaluates to TRUE if it matches at least
one attribute type or subtype in the entry, FALSE if it does not
match any attribute type or subtype in the entry, and Undefined if
the matchingRule is not recognized, the matchingRule is unsuitable
for use with the specified type, or the assertionValue is invalid.
4.5.1.7. SearchRequest.attributes
A selection list of the attributes to be returned from each entry
which matches the search filter. Attributes which are subtypes of
listed attributes are implicitly included. LDAPString values of this
field are constrained to the following Augmented Backus-Naur Form
([ABNF]):
attributeSelector = attributedescription / selectorspecial
Sermersheim Internet-Draft - Expires April 2006 Page 24
Lightweight Directory Access Protocol Version 3
selectorspecial = noattrs / alluserattrs
noattrs = %x31.2E.31 ; "1.1"
alluserattrs = %x2A ; asterisk ("*")
The <attributedescription> production is defined in Section 2.5 of
[Models].
There are three special cases which may appear in the attributes
selection list:
- an empty list with no attributes,
- a list containing "*" (with zero or more attribute
descriptions), and
- a list containing only "1.1".
An empty list requests the return of all user attributes.
A list containing "*" requests the return of all user attributes
in addition to other listed (operational) attributes.
A list containing only the OID "1.1" indicates that no attributes
are to be returned. If "1.1" is provided with other
attributeSelector values, the "1.1" attributeSelector is ignored.
This OID was chosen because it does not (and can not) correspond
to any attribute in use.
Client implementors should note that even if all user attributes are
requested, some attributes and/or attribute values of the entry may
not be included in Search results due to access controls or other
restrictions. Furthermore, servers will not return operational
attributes, such as objectClasses or attributeTypes, unless they are
listed by name. Operational attributes are described in [Models].
Attributes are returned at most once in an entry. If an attribute
description is named more than once in the list, the subsequent names
are ignored. If an attribute description in the list is not
recognized, it is ignored by the server.
4.5.2. Search Result
The results of the Search operation are returned as zero or more
SearchResultEntry and/or SearchResultReference messages, followed by
a single SearchResultDone message.
SearchResultEntry ::= [APPLICATION 4] SEQUENCE {
objectName LDAPDN,
attributes PartialAttributeList }
Sermersheim Internet-Draft - Expires April 2006 Page 25
Lightweight Directory Access Protocol Version 3
PartialAttributeList ::= SEQUENCE OF
partialAttribute PartialAttribute
SearchResultReference ::= [APPLICATION 19] SEQUENCE
SIZE (1..MAX) OF uri URI
SearchResultDone ::= [APPLICATION 5] LDAPResult
Each SearchResultEntry represents an entry found during the Search.
Each SearchResultReference represents an area not yet explored during
the Search. The SearchResultEntry and SearchResultReference messages
may come in any order. Following all the SearchResultReference and
SearchResultEntry responses, the server returns a SearchResultDone
response, which contains an indication of success, or detailing any
errors that have occurred.
Each entry returned in a SearchResultEntry will contain all
appropriate attributes as specified in the attributes field of the
Search Request, subject to access control and other administrative
policy. Note that the PartialAttributeList may hold zero elements.
This may happen when none of the attributes of an entry were
requested, or could be returned. Note also that the partialAttribute
vals set may hold zero elements. This may happen when typesOnly is
requested, access controls prevent the return of values, or other
reasons.
Some attributes may be constructed by the server and appear in a
SearchResultEntry attribute list, although they are not stored
attributes of an entry. Clients SHOULD NOT assume that all attributes
can be modified, even if permitted by access control.
If the server's schema defines short names [Models] for an attribute
type then the server SHOULD use one of those names in attribute
descriptions for that attribute type (in preference to using the
<numericoid> [Models] format of the attribute type's object
identifier). The server SHOULD NOT use the short name if that name is
known by the server to be ambiguous, or otherwise likely to cause
interoperability problems.
4.5.3. Continuation References in the Search Result
If the server was able to locate the entry referred to by the
baseObject but was unable or unwilling to search one or more non-
local entries, the server may return one or more
SearchResultReference messages, each containing a reference to
another set of servers for continuing the operation. A server MUST
NOT return any SearchResultReference messages if it has not located
the baseObject and thus has not searched any entries; in this case it
would return a SearchResultDone containing either a referral or
noSuchObject result code (depending on the server's knowledge of the
entry named in the baseObject).
Sermersheim Internet-Draft - Expires April 2006 Page 26
Lightweight Directory Access Protocol Version 3
If a server holds a copy or partial copy of the subordinate naming
context (Section 5 of [Models]), it may use the search filter to
determine whether or not to return a SearchResultReference response.
Otherwise SearchResultReference responses are always returned when in
scope.
The SearchResultReference is of the same data type as the Referral.
If the client wishes to progress the Search, it issues a new Search
operation for each SearchResultReference that is returned. If
multiple URIs are present, the client assumes that any supported URI
may be used to progress the operation.
Clients that follow search continuation references MUST ensure that
they do not loop between servers. They MUST NOT repeatedly contact
the same server for the same request with the same parameters. Some
clients use a counter that is incremented each time search result
reference handling occurs for an operation, and these kinds of
clients MUST be able to handle at least ten nested referrals while
progressing the operation.
Note that the Abandon operation described in Section 4.11 applies
only to a particular operation sent at the LDAP message layer between
a client and server. The client must abandon subsequent Search
operations it wishes to individually.
A URI for a server implementing LDAP and accessible via [TCP]/[IP]
(v4 or v6) is written as an LDAP URL according to [LDAPURL].
SearchResultReference values which are LDAP URLs follow these rules:
- The <dn> part of the LDAP URL MUST be present, with the new target
object name. The client uses this name when following the
reference.
- Some servers (e.g. participating in distributed indexing) may
provide a different filter in the LDAP URL.
- If the <filter> part of the LDAP URL is present, the client uses
this filter in its next request to progress this Search, and if it
is not present the client uses the same filter as it used for that
Search.
- If the originating search scope was singleLevel, the <scope> part
of the LDAP URL will be "base".
- It is RECOMMENDED that the <scope> part be present to avoid
ambiguity. In the absence of a <scope> part, the scope of the
original Search request is assumed.
- Other aspects of the new Search request may be the same as or
different from the Search request which generated the
SearchResultReference.
Sermersheim Internet-Draft - Expires April 2006 Page 27
Lightweight Directory Access Protocol Version 3
- The name of an unexplored subtree in a SearchResultReference need
not be subordinate to the base object.
Other kinds of URIs may be returned. The syntax and semantics of such
URIs is left to future specifications. Clients may ignore URIs that
they do not support.
UTF-8 encoded characters appearing in the string representation of a
DN, search filter, or other fields of the referral value may not be
legal for URIs (e.g. spaces) and MUST be escaped using the % method
in [URI].
4.5.3.1. Examples
For example, suppose the contacted server (hosta) holds the entry
<DC=Example,DC=NET> and the entry <CN=Manager,DC=Example,DC=NET>. It
knows that both LDAP servers (hostb) and (hostc) hold
<OU=People,DC=Example,DC=NET> (one is the master and the other server
a shadow), and that LDAP-capable server (hostd) holds the subtree
<OU=Roles,DC=Example,DC=NET>. If a wholeSubtree Search of
<DC=Example,DC=NET> is requested to the contacted server, it may
return the following:
SearchResultEntry for DC=Example,DC=NET
SearchResultEntry for CN=Manager,DC=Example,DC=NET
SearchResultReference {
ldap://hostb/OU=People,DC=Example,DC=NET??sub
ldap://hostc/OU=People,DC=Example,DC=NET??sub }
SearchResultReference {
ldap://hostd/OU=Roles,DC=Example,DC=NET??sub }
SearchResultDone (success)
Client implementors should note that when following a
SearchResultReference, additional SearchResultReference may be
generated. Continuing the example, if the client contacted the server
(hostb) and issued the Search request for the subtree
<OU=People,DC=Example,DC=NET>, the server might respond as follows:
SearchResultEntry for OU=People,DC=Example,DC=NET
SearchResultReference {
ldap://hoste/OU=Managers,OU=People,DC=Example,DC=NET??sub }
SearchResultReference {
ldap://hostf/OU=Consultants,OU=People,DC=Example,DC=NET??sub }
SearchResultDone (success)
Similarly, if a singleLevel Search of <DC=Example,DC=NET> is
requested to the contacted server, it may return the following:
Sermersheim Internet-Draft - Expires April 2006 Page 28
Lightweight Directory Access Protocol Version 3
SearchResultEntry for CN=Manager,DC=Example,DC=NET
SearchResultReference {
ldap://hostb/OU=People,DC=Example,DC=NET??base
ldap://hostc/OU=People,DC=Example,DC=NET??base }
SearchResultReference {
ldap://hostd/OU=Roles,DC=Example,DC=NET??base }
SearchResultDone (success)
If the contacted server does not hold the base object for the Search,
but has knowledge of its possible location, then it may return a
referral to the client. In this case, if the client requests a
subtree Search of <DC=Example,DC=ORG> to hosta, the server returns a
SearchResultDone containing a referral.
SearchResultDone (referral) {
ldap://hostg/DC=Example,DC=ORG??sub }
4.6. Modify Operation
The Modify operation allows a client to request that a modification
of an entry be performed on its behalf by a server. The Modify
Request is defined as follows:
ModifyRequest ::= [APPLICATION 6] SEQUENCE {
object LDAPDN,
changes SEQUENCE OF change SEQUENCE {
operation ENUMERATED {
add (0),
delete (1),
replace (2),
... },
modification PartialAttribute } }
Fields of the Modify Request are:
- object: The value of this field contains the name of the entry to
be modified. The server SHALL NOT perform any alias dereferencing
in determining the object to be modified.
- changes: A list of modifications to be performed on the entry. The
entire list of modifications MUST be performed in the order they
are listed as a single atomic operation. While individual
modifications may violate certain aspects of the directory schema
(such as the object class definition and DIT content rule), the
resulting entry after the entire list of modifications is
performed MUST conform to the requirements of the directory model
and controlling schema [Models].
- operation: Used to specify the type of modification being
performed. Each operation type acts on the following
modification. The values of this field have the following
semantics respectively:
Sermersheim Internet-Draft - Expires April 2006 Page 29
Lightweight Directory Access Protocol Version 3
add: add values listed to the modification attribute,
creating the attribute if necessary;
delete: delete values listed from the modification attribute.
If no values are listed, or if all current values of the
attribute are listed, the entire attribute is removed;
replace: replace all existing values of the modification
attribute with the new values listed, creating the attribute
if it did not already exist. A replace with no value will
delete the entire attribute if it exists, and is ignored if
the attribute does not exist.
- modification: A PartialAttribute (which may have an empty SET
of vals) used to hold the attribute type or attribute type and
values being modified.
Upon receipt of a Modify Request, the server attempts to perform the
necessary modifications to the DIT and returns the result in a Modify
Response, defined as follows:
ModifyResponse ::= [APPLICATION 7] LDAPResult
The server will return to the client a single Modify Response
indicating either the successful completion of the DIT modification,
or the reason that the modification failed. Due to the requirement
for atomicity in applying the list of modifications in the Modify
Request, the client may expect that no modifications of the DIT have
been performed if the Modify Response received indicates any sort of
error, and that all requested modifications have been performed if
the Modify Response indicates successful completion of the Modify
operation. Whether the modification was applied or not cannot be
determined by the client if the Modify Response was not received
(e.g. the LDAP session was terminated or the Modify operation was
abandoned).
Servers MUST ensure that entries conform to user and system schema
rules or other data model constraints. The Modify operation cannot be
used to remove from an entry any of its distinguished values, i.e.
those values which form the entry's relative distinguished name. An
attempt to do so will result in the server returning the
notAllowedOnRDN result code. The Modify DN operation described in
Section 4.9 is used to rename an entry.
For attribute types which specify no equality matching, the rules in
Section 2.5.1 of [Models] are followed.
Note that due to the simplifications made in LDAP, there is not a
direct mapping of the changes in an LDAP ModifyRequest onto the
changes of a DAP ModifyEntry operation, and different implementations
of LDAP-DAP gateways may use different means of representing the
change. If successful, the final effect of the operations on the
entry MUST be identical.
Sermersheim Internet-Draft - Expires April 2006 Page 30
Lightweight Directory Access Protocol Version 3
4.7. Add Operation
The Add operation allows a client to request the addition of an entry
into the Directory. The Add Request is defined as follows:
AddRequest ::= [APPLICATION 8] SEQUENCE {
entry LDAPDN,
attributes AttributeList }
AttributeList ::= SEQUENCE OF attribute Attribute
Fields of the Add Request are:
- entry: the name of the entry to be added. The server SHALL NOT
dereference any aliases in locating the entry to be added.
- attributes: the list of attributes that, along with those from the
RDN, make up the content of the entry being added. Clients MAY or
MAY NOT include the RDN attribute(s) in this list. Clients MUST
NOT supply NO-USER-MODIFICATION attributes such as the
createTimestamp or creatorsName attributes, since the server
maintains these automatically.
Servers MUST ensure that entries conform to user and system schema
rules or other data model constraints. For attribute types which
specify no equality matching, the rules in Section 2.5.1 of [Models]
are followed (this applies to the naming attribute in addition to any
multi-valued attributes being added).
The entry named in the entry field of the AddRequest MUST NOT exist
for the AddRequest to succeed. The immediate superior (parent) of an
object or alias entry to be added MUST exist. For example, if the
client attempted to add <CN=JS,DC=Example,DC=NET>, the
<DC=Example,DC=NET> entry did not exist, and the <DC=NET> entry did
exist, then the server would return the noSuchObject result code with
the matchedDN field containing <DC=NET>.
Upon receipt of an Add Request, a server will attempt to add the
requested entry. The result of the Add attempt will be returned to
the client in the Add Response, defined as follows:
AddResponse ::= [APPLICATION 9] LDAPResult
A response of success indicates that the new entry has been added to
the Directory.
4.8. Delete Operation
The Delete operation allows a client to request the removal of an
entry from the Directory. The Delete Request is defined as follows:
DelRequest ::= [APPLICATION 10] LDAPDN
Sermersheim Internet-Draft - Expires April 2006 Page 31
Lightweight Directory Access Protocol Version 3
The Delete Request consists of the name of the entry to be deleted.
The server SHALL NOT dereference aliases while resolving the name of
the target entry to be removed.
Only leaf entries (those with no subordinate entries) can be deleted
with this operation.
Upon receipt of a Delete Request, a server will attempt to perform
the entry removal requested and return the result in the Delete
Response defined as follows:
DelResponse ::= [APPLICATION 11] LDAPResult
4.9. Modify DN Operation
The Modify DN operation allows a client to change the Relative
Distinguished Name (RDN) of an entry in the Directory, and/or to move
a subtree of entries to a new location in the Directory. The Modify
DN Request is defined as follows:
ModifyDNRequest ::= [APPLICATION 12] SEQUENCE {
entry LDAPDN,
newrdn RelativeLDAPDN,
deleteoldrdn BOOLEAN,
newSuperior [0] LDAPDN OPTIONAL }
Fields of the Modify DN Request are:
- entry: the name of the entry to be changed. This entry may or may
not have subordinate entries.
- newrdn: the new RDN of the entry. The value of the old RDN is
supplied when moving the entry to a new superior without changing
its RDN. Attribute values of the new RDN not matching any
attribute value of the entry are added to the entry and an
appropriate error is returned if this fails.
- deleteoldrdn: a boolean field that controls whether the old RDN
attribute values are to be retained as attributes of the entry, or
deleted from the entry.
- newSuperior: if present, this is the name of an existing object
entry which becomes the immediate superior (parent) of the
existing entry.
The server SHALL NOT dereference any aliases in locating the objects
named in entry or newSuperior.
Upon receipt of a ModifyDNRequest, a server will attempt to perform
the name change and return the result in the Modify DN Response,
defined as follows:
Sermersheim Internet-Draft - Expires April 2006 Page 32
Lightweight Directory Access Protocol Version 3
ModifyDNResponse ::= [APPLICATION 13] LDAPResult
For example, if the entry named in the entry field was <cn=John
Smith,c=US>, the newrdn field was <cn=John Cougar Smith>, and the
newSuperior field was absent, then this operation would attempt to
rename the entry to be <cn=John Cougar Smith,c=US>. If there was
already an entry with that name, the operation would fail with the
entryAlreadyExists result code.
Servers MUST ensure that entries conform to user and system schema
rules or other data model constraints. For attribute types which
specify no equality matching, the rules in Section 2.5.1 of [Models]
are followed (this pertains to newrdn and deleteoldrdn).
The object named in newSuperior MUST exist. For example, if the
client attempted to add <CN=JS,DC=Example,DC=NET>, the
<DC=Example,DC=NET> entry did not exist, and the <DC=NET> entry did
exist, then the server would return the noSuchObject result code with
the matchedDN field containing <DC=NET>.
If the deleteoldrdn field is TRUE, the attribute values forming the
old RDN but not the new RDN are deleted from the entry. If the
deleteoldrdn field is FALSE, the attribute values forming the old RDN
will be retained as non-distinguished attribute values of the entry.
Note that X.500 restricts the ModifyDN operation to only affect
entries that are contained within a single server. If the LDAP server
is mapped onto DAP, then this restriction will apply, and the
affectsMultipleDSAs result code will be returned if this error
occurred. In general, clients MUST NOT expect to be able to perform
arbitrary movements of entries and subtrees between servers or
between naming contexts.
4.10. Compare Operation
The Compare operation allows a client to compare an assertion value
with the values of a particular attribute in a particular entry in
the Directory. The Compare Request is defined as follows:
CompareRequest ::= [APPLICATION 14] SEQUENCE {
entry LDAPDN,
ava AttributeValueAssertion }
Fields of the Compare Request are:
- entry: the name of the entry to be compared. The server SHALL NOT
dereference any aliases in locating the entry to be compared.
- ava: holds the attribute value assertion to be compared.
Upon receipt of a Compare Request, a server will attempt to perform
the requested comparison and return the result in the Compare
Response, defined as follows:
Sermersheim Internet-Draft - Expires April 2006 Page 33
Lightweight Directory Access Protocol Version 3
CompareResponse ::= [APPLICATION 15] LDAPResult
The resultCode is set to compareTrue, compareFalse, or an appropriate
error. compareTrue indicates that the assertion value in the ava
field matches a value of the attribute or subtype according to the
attribute's EQUALITY matching rule. compareFalse indicates that the
assertion value in the ava field and the values of the attribute or
subtype did not match. Other result codes indicate either that the
result of the comparison was Undefined (Section 4.5.1), or that some
error occurred.
Note that some directory systems may establish access controls which
permit the values of certain attributes (such as userPassword) to be
compared but not interrogated by other means.
4.11. Abandon Operation
The function of the Abandon operation is to allow a client to request
that the server abandon an uncompleted operation. The Abandon Request
is defined as follows:
AbandonRequest ::= [APPLICATION 16] MessageID
The MessageID is that of an operation which was requested earlier at
this LDAP message layer. The Abandon request itself has its own
MessageID. This is distinct from the MessageID of the earlier
operation being abandoned.
There is no response defined in the Abandon operation. Upon receipt
of an AbandonRequest, the server MAY abandon the operation identified
by the MessageID. Since the client cannot tell the difference between
a successfully abandoned operation and an uncompleted operation, the
application of the Abandon operation is limited to uses where the
client does not require an indication of its outcome.
Abandon, Bind, Unbind, and StartTLS operations cannot be abandoned.
In the event that a server receives an Abandon Request on a Search
operation in the midst of transmitting responses to the Search, that
server MUST cease transmitting entry responses to the abandoned
request immediately, and MUST NOT send the SearchResultDone. Of
course, the server MUST ensure that only properly encoded LDAPMessage
PDUs are transmitted.
The ability to abandon other (particularly update) operations is at
the discretion of the server.
Clients should not send Abandon requests for the same operation
multiple times, and MUST also be prepared to receive results from
operations it has abandoned (since these may have been in transit
when the Abandon was requested, or are not able to be abandoned).
Sermersheim Internet-Draft - Expires April 2006 Page 34
Lightweight Directory Access Protocol Version 3
Servers MUST discard Abandon requests for message IDs they do not
recognize, for operations which cannot be abandoned, and for
operations which have already been abandoned.
4.12. Extended Operation
The Extended operation allows additional operations to be defined for
services not already available in the protocol. For example, to Add
operations to install transport layer security (see Section 4.14).
The Extended operation allows clients to make requests and receive
responses with predefined syntaxes and semantics. These may be
defined in RFCs or be private to particular implementations.
Each Extended operation consists of an Extended request and an
Extended response.
ExtendedRequest ::= [APPLICATION 23] SEQUENCE {
requestName [0] LDAPOID,
requestValue [1] OCTET STRING OPTIONAL }
The requestName is a dotted-decimal representation of the unique
OBJECT IDENTIFIER corresponding to the request. The requestValue is
information in a form defined by that request, encapsulated inside an
OCTET STRING.
The server will respond to this with an LDAPMessage containing an
ExtendedResponse.
ExtendedResponse ::= [APPLICATION 24] SEQUENCE {
COMPONENTS OF LDAPResult,
responseName [10] LDAPOID OPTIONAL,
responseValue [11] OCTET STRING OPTIONAL }
The responseName field, when present, contains an LDAPOID which is
unique for this extended operation or response. This field is
optional (even when the extension specification specifies an LDAPOID
to be returned in the field). The field will be absent whenever the
server is unable or unwilling to determine the appropriate LDAPOID to
return, for instance when the requestName cannot be parsed or its
value is not recognized.
Where the requestName is not recognized, the server returns
protocolError (The server may return protocolError in other cases).
The requestValue and responseValue fields contain information
associated with the operation. The format of these fields is defined
by the specification of the Extended operation. Implementations MUST
be prepared to handle arbitrary contents of these fields, including
zero bytes. Values that are defined in terms of ASN.1 and BER encoded
according to Section 5.1, also follow the extensibility rules in
Section 4.
Sermersheim Internet-Draft - Expires April 2006 Page 35
Lightweight Directory Access Protocol Version 3
Servers list the requestName of Extended Requests they recognize in
the 'supportedExtension' attribute in the root DSE (Section 5.1 of
[Models]).
Extended operations may be specified in other documents. The
specification of an Extended operation consists of:
- the OBJECT IDENTIFIER assigned to the requestName,
- the OBJECT IDENTIFIER (if any) assigned to the responseName (note
that the same OBJECT IDENTIFIER may be used for both the
requestName and responseName),
- the format of the contents of the requestValue and responseValue
(if any), and
- the semantics of the operation.
4.13. IntermediateResponse Message
While the Search operation provides a mechanism to return multiple
response messages for a single Search request, other operations, by
nature, do not provide for multiple response messages.
The IntermediateResponse message provides a general mechanism for
defining single-request/multiple-response operations in LDAP. This
message is intended to be used in conjunction with the Extended
operation to define new single-request/multiple-response operations
or in conjunction with a control when extending existing LDAP
operations in a way that requires them to return Intermediate
response information.
It is intended that the definitions and descriptions of Extended
operations and controls that make use of the IntermediateResponse
message will define the circumstances when an IntermediateResponse
message can be sent by a server and the associated meaning of an
IntermediateResponse message sent in a particular circumstance.
IntermediateResponse ::= [APPLICATION 25] SEQUENCE {
responseName [0] LDAPOID OPTIONAL,
responseValue [1] OCTET STRING OPTIONAL }
IntermediateResponse messages SHALL NOT be returned to the client
unless the client issues a request that specifically solicits their
return. This document defines two forms of solicitation: Extended
operation and request control. IntermediateResponse messages are
specified in documents describing the manner in which they are
solicited (i.e. in the Extended operation or request control
specification that uses them). These specifications include:
- the OBJECT IDENTIFIER (if any) assigned to the responseName,
- the format of the contents of the responseValue (if any), and
Sermersheim Internet-Draft - Expires April 2006 Page 36
Lightweight Directory Access Protocol Version 3
- the semantics associated with the IntermediateResponse message.
Extensions that allow the return of multiple types of
IntermediateResponse messages SHALL identify those types using unique
responseName values (note that one of these may specify no value).
Sections 4.13.1 and 4.13.2 describe additional requirements on the
inclusion of responseName and responseValue in IntermediateResponse
messages.
4.13.1. Usage with LDAP ExtendedRequest and ExtendedResponse
A single-request/multiple-response operation may be defined using a
single ExtendedRequest message to solicit zero or more
IntermediateResponse messages of one or more kinds followed by an
ExtendedResponse message.
4.13.2. Usage with LDAP Request Controls
A control's semantics may include the return of zero or more
IntermediateResponse messages prior to returning the final result
code for the operation. One or more kinds of IntermediateResponse
messages may be sent in response to a request control.
All IntermediateResponse messages associated with request controls
SHALL include a responseName. This requirement ensures that the
client can correctly identify the source of IntermediateResponse
messages when:
- two or more controls using IntermediateResponse messages are
included in a request for any LDAP operation or
- one or more controls using IntermediateResponse messages are
included in a request with an LDAP Extended operation that uses
IntermediateResponse messages.
4.14. StartTLS Operation
The Start Transport Layer Security (StartTLS) operation's purpose is
to initiate installation of a TLS layer. The StartTLS operation is
defined using the Extended operation mechanism described in Section
4.12.
Sermersheim Internet-Draft - Expires April 2006 Page 37
Lightweight Directory Access Protocol Version 3
4.14.1. StartTLS Request
A client requests TLS establishment by transmitting a StartTLS
request message to the server. The StartTLS request is defined in
terms of an ExtendedRequest. The requestName is
"1.3.6.1.4.1.1466.20037", and the requestValue field is always
absent.
The client MUST NOT send any LDAP PDUs at this LDAP message layer
following this request until it receives a StartTLS Extended response
and, in the case of a successful response, completes TLS
negotiations.
Detected sequencing problems (particularly those detailed in Section
3.1.1 of [AuthMeth]) result in the resultCode being set to
operationsError.
If the server does not support TLS (whether by design or by current
configuration), it returns with the resultCode set to protocolError
as described in Section 4.12.
4.14.2. StartTLS Response
When a StartTLS request is received, servers supporting the operation
MUST return a StartTLS response message to the requestor. The
responseName is "1.3.6.1.4.1.1466.20037" when provided (See 4.12).
The responseValue is always absent.
If the server is willing and able to negotiate TLS, it returns the
StartTLS response with the resultCode set to success. Upon client
receipt of a successful StartTLS response, protocol peers may
commence with TLS negotiation as discussed in Section 3 of
[AuthMeth].
If the server is otherwise unwilling or unable to perform this
operation, the server is to return an appropriate result code
indicating the nature of the problem. For example, if the TLS
subsystem is not presently available, the server may indicate so by
returning with the resultCode set to unavailable. In cases where a
non-success result code is returned, the LDAP session is left without
a TLS layer.
4.14.3. Removal of the TLS Layer
Either the client or server MAY remove the TLS layer and leave the
LDAP message layer intact by sending and receiving a TLS closure
alert.
Sermersheim Internet-Draft - Expires April 2006 Page 38
Lightweight Directory Access Protocol Version 3
The initiating protocol peer sends the TLS closure alert and MUST
wait until it receives a TLS closure alert from the other peer before
sending further LDAP PDUs.
When a protocol peer receives the initial TLS closure alert, it may
choose to allow the LDAP message layer to remain intact. In this
case, it MUST immediately transmit a TLS closure alert. Following
this, it MAY send and receive LDAP PDUs.
Protocol peers MAY terminate the LDAP session after sending or
receiving a TLS closure alert.
5. Protocol Encoding, Connection, and Transfer
This protocol is designed to run over connection-oriented, reliable
transports, where the data stream is divided into octets (8-bit
units), with each octet and each bit being significant.
One underlying service, LDAP over TCP, is defined in Section
5.2. This service is generally applicable to applications providing
or consuming X.500-based directory services on the Internet. This
specification was generally written with the TCP mapping in mind.
Specifications detailing other mappings may encounter various
obstacles.
Implementations of LDAP over TCP MUST implement the mapping as
described in Section 5.2.
This table illustrates the relationship between the different layers
involved in an exchange between two protocol peers:
+----------------------+
| LDAP message layer |
+----------------------+ > LDAP PDUs
+----------------------+ < data
| SASL layer |
+----------------------+ > SASL-protected data
+----------------------+ < data
| TLS layer |
Application +----------------------+ > TLS-protected data
------------+----------------------+ < data
Transport | transport connection |
+----------------------+
5.1. Protocol Encoding
The protocol elements of LDAP SHALL be encoded for exchange using the
Basic Encoding Rules [BER] of [ASN.1] with the following
restrictions:
- Only the definite form of length encoding is used.
Sermersheim Internet-Draft - Expires April 2006 Page 39
Lightweight Directory Access Protocol Version 3
- OCTET STRING values are encoded in the primitive form only.
- If the value of a BOOLEAN type is true, the encoding of the value
octet is set to hex "FF".
- If a value of a type is its default value, it is absent. Only some
BOOLEAN and INTEGER types have default values in this protocol
definition.
These restrictions are meant to ease the overhead of encoding and
decoding certain elements in BER.
These restrictions do not apply to ASN.1 types encapsulated inside of
OCTET STRING values, such as attribute values, unless otherwise
stated.
5.2. Transmission Control Protocol (TCP)
The encoded LDAPMessage PDUs are mapped directly onto the [TCP]
bytestream using the BER-based encoding described in Section 5.1. It
is recommended that server implementations running over the TCP
provide a protocol listener on the Internet Assigned Numbers
Authority (IANA)-assigned LDAP port, 389 [PortReg]. Servers may
instead provide a listener on a different port number. Clients MUST
support contacting servers on any valid TCP port.
5.3. Termination of the LDAP session
Termination of the LDAP session is typically initiated by the client
sending an UnbindRequest (Section 4.3), or by the server sending a
Notice of Disconnection (Section 4.4.1). In these cases each protocol
peer gracefully terminates the LDAP session by ceasing exchanges at
the LDAP message layer, tearing down any SASL layer, tearing down any
TLS layer, and closing the transport connection.
A protocol peer may determine that the continuation of any
communication would be pernicious, and in this case may abruptly
terminate the session by ceasing communication and closing the
transport connection.
In either case, when the LDAP session is terminated, uncompleted
operations are handled as specified in Section 3.1.
6. Security Considerations
This version of the protocol provides facilities for simple
authentication using a cleartext password, as well as any [SASL]
mechanism. Installing SASL and/or TLS layers can provide integrity
and other data security services.
Sermersheim Internet-Draft - Expires April 2006 Page 40
Lightweight Directory Access Protocol Version 3
It is also permitted that the server can return its credentials to
the client, if it chooses to do so.
Use of cleartext password is strongly discouraged where the
underlying transport service cannot guarantee confidentiality and may
result in disclosure of the password to unauthorized parties.
Servers are encouraged to prevent directory modifications by clients
that have authenticated anonymously [AuthMeth].
Security considerations for authentication methods, SASL mechanisms,
and TLS are described in [AuthMeth].
It should be noted that SASL authentication exchanges do not provide
data confidentiality nor integrity protection for the version or name
fields of the BindRequest nor the resultCode, diagnosticMessage, or
referral fields of the BindResponse nor of any information contained
in controls attached to Bind requests or responses. Thus information
contained in these fields SHOULD NOT be relied on unless otherwise
protected (such as by establishing protections at the transport
layer).
Implementors should note that various security factors, including
authentication and authorization information and data security
services may change during the course of the LDAP session, or even
during the performance of a particular operation. For instance,
credentials could expire, authorization identities or access controls
could change, or the underlying security layer(s) could be replaced
or terminated. Implementations should be robust in the handling of
changing security factors.
In some cases, it may be appropriate to continue the operation even
in light of security factor changes. For instance, it may be
appropriate to continue an Abandon operation regardless of the
change, or to continue an operation when the change upgraded (or
maintained) the security factor. In other cases, it may be
appropriate to fail, or alter the processing of the operation. For
instance, if confidential protections were removed, it would be
appropriate to either fail a request to return sensitive data, or
minimally, to exclude the return of sensitive data.
Implementations which cache attributes and entries obtained via LDAP
MUST ensure that access controls are maintained if that information
is to be provided to multiple clients, since servers may have access
control policies which prevent the return of entries or attributes in
Search results except to particular authenticated clients. For
example, caches could serve result information only to the client
whose request caused it to be in the cache.
Sermersheim Internet-Draft - Expires April 2006 Page 41
Lightweight Directory Access Protocol Version 3
Servers may return referrals or Search result references which
redirect clients to peer servers. It is possible for a rogue
application to inject such referrals into the data stream in an
attempt to redirect a client to a rogue server. Clients are advised
to be aware of this, and possibly reject referrals when
confidentiality measures are not in place. Clients are advised to
reject referrals from the StartTLS operation.
The matchedDN and diagnosticMessage fields, as well as some
resultCode values (e.g., attributeOrValueExists and
entryAlreadyExists), could disclose the presence or absence of
specific data in the directory which is subject to access and other
administrative controls. Server implementations should restrict
access to protected information equally under both normal and error
conditions.
Protocol peers MUST be prepared to handle invalid and arbitrary
length protocol encodings. Invalid protocol encodings include: BER
encoding exceptions, format string and UTF-8 encoding exceptions,
overflow exceptions, integer value exceptions, and binary mode on/off
flag exceptions. The LDAPv3 PROTOS [PROTOS-LDAP] test suite provides
excellent examples of these exceptions and test cases used to
discover flaws.
In the event that a protocol peer senses an attack which in its
nature could cause damage due to further communication at any layer
in the LDAP session, the protocol peer should abruptly terminate the
LDAP session as described in Section 5.3.
7. Acknowledgements
This document is based on RFC 2251 by Mark Wahl, Tim Howes, and Steve
Kille. RFC 2251 was a product of the IETF ASID Working Group.
It is also based on RFC 2830 by Jeff Hodges, RL "Bob" Morgan, and
Mark Wahl. RFC 2830 was a product of the IETF LDAPEXT Working Group.
It is also based on RFC 3771 by Roger Harrison, and Kurt Zeilenga.
RFC 3771 was an individual submission to the IETF.
This document is a product of the IETF LDAPBIS Working Group.
Significant contributors of technical review and content include Kurt
Zeilenga, Steven Legg, and Hallvard Furuseth.
8. Normative References
[ABNF] Crocker, D. and P. Overell, "Augmented BNF for Syntax
Specifications: ABNF", draft-crocker-abnf-rfc2234bis-
xx.txt, (a work in progress).
Sermersheim Internet-Draft - Expires April 2006 Page 42
Lightweight Directory Access Protocol Version 3
[ASN.1] ITU-T Recommendation X.680 (07/2002) | ISO/IEC 8824-1:2002
"Information Technology - Abstract Syntax Notation One
(ASN.1): Specification of basic notation"
[AuthMeth] Harrison, R., "LDAP: Authentication Methods and Connection
Level Security Mechanisms", draft-ietf-ldapbis-authmeth-
xx.txt, (a work in progress).
[BER] ITU-T Rec. X.690 (07/2002) | ISO/IEC 8825-1:2002,
"Information technology - ASN.1 encoding rules:
Specification of Basic Encoding Rules (BER), Canonical
Encoding Rules (CER) and Distinguished Encoding Rules
(DER)", 2002.
[IP] Postel, J., "Internet Protocol", STD5 and RFC 791,
September 1981
[ISO10646] Universal Multiple-Octet Coded Character Set (UCS) -
Architecture and Basic Multilingual Plane, ISO/IEC 10646-1
: 1993.
[Keyword] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", RFC 2119, March 1997.
[LDAPDN] Zeilenga, K., "LDAP: String Representation of
Distinguished Names", draft-ietf-ldapbis-dn-xx.txt, (a
work in progress).
[LDAPIANA] Zeilenga, K., "IANA Considerations for LDAP", draft-ietf-
ldapbis-bcp64-xx.txt, (a work in progress).
[LDAPURL] Smith, M., "LDAP: Uniform Resource Locator", draft-ietf-
ldapbis-url-xx.txt, (a work in progress).
[Models] Zeilenga, K., "LDAP: Directory Information Models", draft-
ietf-ldapbis-models-xx.txt (a work in progress).
[Roadmap] Zeilenga, K., "LDAP: Technical Specification Road Map",
draft-ietf-ldapbis-roadmap-xx.txt (a work in progress).
[SASL] Melnikov, A., "Simple Authentication and Security Layer",
draft-ietf-sasl-rfc2222bis-xx.txt (a work in progress).
[SASLPrep] Zeilenga, K., "Stringprep profile for user names and
passwords", draft-ietf-sasl-saslprep-xx.txt, (a work in
progress).
[StringPrep] Hoffman P. and M. Blanchet, "Preparation of
Internationalized Strings ('stringprep')", draft-hoffman-
rfc3454bis-xx.txt, a work in progress.
[Syntaxes] Legg, S., and K. Dally, "LDAP: Syntaxes and Matching
Rules", draft-ietf-ldapbis-syntaxes-xx.txt, (a work in
progress).
Sermersheim Internet-Draft - Expires April 2006 Page 43
Lightweight Directory Access Protocol Version 3
[TCP] Postel, J., "Transmission Control Protocol", STD7 and RFC
793, September 1981
[TLS] Dierks, T. and C. Allen. "The TLS Protocol Version 1.1",
draft-ietf-tls-rfc2246-bis-xx.txt, a work in progress.
[Unicode] The Unicode Consortium, "The Unicode Standard, Version
3.2.0" is defined by "The Unicode Standard, Version 3.0"
(Reading, MA, Addison-Wesley, 2000. ISBN 0-201-61633-5),
as amended by the "Unicode Standard Annex #27: Unicode
3.1" (http://www.unicode.org/reports/tr27/) and by the
"Unicode Standard Annex #28: Unicode 3.2"
(http://www.unicode.org/reports/tr28/).
[URI] Berners-Lee, T., Fielding, R., and L. Masinter, "Uniform
Resource Identifiers (URI): Generic Syntax", RFC 2396,
August 1998.
[UTF-8] Yergeau, F., "UTF-8, a transformation format of ISO
10646", STD63 and RFC3629, November 2003.
[X.500] ITU-T Rec. X.500, "The Directory: Overview of Concepts,
Models and Service", 1993.
[X.501] ITU-T Rec. X.501, "The Directory: Models", 1993.
[X.511] ITU-T Rec. X.511, "The Directory: Abstract Service
Definition", 1993.
9. Informative References
[Glossary] The Unicode Consortium, "Unicode Glossary",
<http://www.unicode.org/glossary/>.
[CharModel] Whistler, K. and M. Davis, "Unicode Technical Report
#17, Character Encoding Model", UTR17,
<http://www.unicode.org/unicode/reports/tr17/>, August
2000.
[PROTOS-LDAP] University of Oulu, "PROTOS Test-Suite: c06-ldapv3"
<http://www.ee.oulu.fi/research/ouspg/protos/testing/c06/l
dapv3/>
[PortReg] IANA, "Port Numbers",
http://www.iana.org/assignments/port-numbers
10. IANA Considerations
Sermersheim Internet-Draft - Expires April 2006 Page 44
Lightweight Directory Access Protocol Version 3
It is requested that the Internet Assigned Numbers Authority (IANA)
update the LDAP result code registry to indicate that this document
provides the definitive technical specification for result codes 0-
36, 48-54, 64-70, 80-90. It is also noted that one resultCode value
(strongAuthRequired) has been renamed (to strongerAuthRequired).
It is requested that the IANA update the LDAP Protocol Mechanism
registry to indicate that this document and [AuthMeth] provides the
definitive technical specification for the StartTLS
(1.3.6.1.4.1.1466.20037) Extended operation.
It is requested that the IANA update the occurrence of "RFC XXXX" in
this section and Appendix B with this RFC number at publication.
It is requested that IANA assign upon Standards Action an LDAP Object
Identifier [LDAPIANA] to identify the ASN.1 module defined in this
document.
Subject: Request for LDAP Object Identifier Registration
Person & email address to contact for further information:
Jim Sermersheim <[email protected]>
Specification: RFC XXXX
Author/Change Controller: IESG
Comments:
Identifies the LDAP ASN.1 module
[[Note to RFC Editor: please replace the occurrence of <IANA-
ASSIGNED-DIRECTORY-NUMBER> in Appendix B with the IANA assigned
OID.]]
11. Editor's Address
Jim Sermersheim
Novell, Inc.
1800 South Novell Place
Provo, Utah 84606, USA
[email protected]
+1 801 861-3088
Sermersheim Internet-Draft - Expires April 2006 Page 45
Lightweight Directory Access Protocol Version 3
Appendix A. LDAP Result Codes
This normative appendix details additional considerations regarding
LDAP result codes and provides a brief, general description of each
LDAP result code enumerated in Section 4.1.9.
Additional result codes MAY be defined for use with extensions
[LDAPIANA]. Client implementations SHALL treat any result code which
they do not recognize as an unknown error condition.
The descriptions provided here do not fully account for result code
substitutions used to prevent unauthorized disclosures (such as
substitution of noSuchObject for insufficientAccessRights, or
invalidCredentials for insufficientAccessRights).
A.1. Non-Error Result Codes
These result codes (called "non-error" result codes) do not indicate
an error condition:
success (0),
compareFalse (5),
compareTrue (6),
referral (10), and
saslBindInProgress (14).
The success, compareTrue, and compareFalse result codes indicate
successful completion (and, hence, are referred to as "successful"
result codes).
The referral and saslBindInProgress result codes indicate the client
needs to take additional action to complete the operation.
A.2. Result Codes
Existing LDAP result codes are described as follows:
success (0)
Indicates the successful completion of an operation. Note:
this code is not used with the Compare operation. See
compareFalse (5) and compareTrue (6).
operationsError (1)
Indicates that the operation is not properly sequenced with
relation to other operations (of same or different type).
For example, this code is returned if the client attempts to
StartTLS [TLS] while there are other uncompleted operations
or if a TLS layer was already installed.
protocolError (2)
Indicates the server received data which is not well-formed.
Sermersheim Internet-Draft - Expires April 2006 Page 46
Lightweight Directory Access Protocol Version 3
For Bind operation only, this code is also used to indicate
that the server does not support the requested protocol
version.
For Extended operations only, this code is also used to
indicate that the server does not support (by design or
configuration) the Extended operation associated with the
requestName.
For request operations specifying multiple controls, this may
be used to indicate that the server cannot ignore the order
of the controls as specified, or that the combination of the
specified controls is invalid or unspecified.
timeLimitExceeded (3)
Indicates that the time limit specified by the client was
exceeded before the operation could be completed.
sizeLimitExceeded (4)
Indicates that the size limit specified by the client was
exceeded before the operation could be completed.
compareFalse (5)
Indicates that the Compare operation has successfully
completed and the assertion has evaluated to FALSE or
Undefined.
compareTrue (6)
Indicates that the Compare operation has successfully
completed and the assertion has evaluated to TRUE.
authMethodNotSupported (7)
Indicates that the authentication method or mechanism is not
supported.
strongerAuthRequired (8)
Indicates the server requires strong(er) authentication in
order to complete the operation.
When used with the Notice of Disconnection operation, this
code indicates that the server has detected that an
established security association between the client and
server has unexpectedly failed or been compromised.
referral (10)
Indicates that a referral needs to be chased to complete the
operation (see Section 4.1.10).
adminLimitExceeded (11)
Indicates that an administrative limit has been exceeded.
unavailableCriticalExtension (12)
Indicates a critical control is unrecognized (see Section
4.1.11).
Sermersheim Internet-Draft - Expires April 2006 Page 47
Lightweight Directory Access Protocol Version 3
confidentialityRequired (13)
Indicates that data confidentiality protections are required.
saslBindInProgress (14)
Indicates the server requires the client to send a new bind
request, with the same SASL mechanism, to continue the
authentication process (see Section 4.2).
noSuchAttribute (16)
Indicates that the named entry does not contain the specified
attribute or attribute value.
undefinedAttributeType (17)
Indicates that a request field contains an unrecognized
attribute description.
inappropriateMatching (18)
Indicates that an attempt was made (e.g. in an assertion) to
use a matching rule not defined for the attribute type
concerned.
constraintViolation (19)
Indicates that the client supplied an attribute value which
does not conform to the constraints placed upon it by the
data model.
For example, this code is returned when multiple values are
supplied to an attribute which has a SINGLE-VALUE constraint.
attributeOrValueExists (20)
Indicates that the client supplied an attribute or value to
be added to an entry, but the attribute or value already
exists.
invalidAttributeSyntax (21)
Indicates that a purported attribute value does not conform
to the syntax of the attribute.
noSuchObject (32)
Indicates that the object does not exist in the DIT.
aliasProblem (33)
Indicates that an alias problem has occurred. For example,
the code may used to indicate an alias has been dereferenced
which names no object.
invalidDNSyntax (34)
Indicates that an LDAPDN or RelativeLDAPDN field (e.g. search
base, target entry, ModifyDN newrdn, etc.) of a request does
not conform to the required syntax or contains attribute
values which do not conform to the syntax of the attribute's
type.
Sermersheim Internet-Draft - Expires April 2006 Page 48
Lightweight Directory Access Protocol Version 3
aliasDereferencingProblem (36)
Indicates that a problem occurred while dereferencing an
alias. Typically an alias was encountered in a situation
where it was not allowed or where access was denied.
inappropriateAuthentication (48)
Indicates the server requires the client which had attempted
to bind anonymously or without supplying credentials to
provide some form of credentials.
invalidCredentials (49)
Indicates that the provided credentials (e.g. the user's name
and password) are invalid.
insufficientAccessRights (50)
Indicates that the client does not have sufficient access
rights to perform the operation.
busy (51)
Indicates that the server is too busy to service the
operation.
unavailable (52)
Indicates that the server is shutting down or a subsystem
necessary to complete the operation is offline.
unwillingToPerform (53)
Indicates that the server is unwilling to perform the
operation.
loopDetect (54)
Indicates that the server has detected an internal loop (e.g.
while dereferencing aliases or chaining an operation).
namingViolation (64)
Indicates that the entry's name violates naming restrictions.
objectClassViolation (65)
Indicates that the entry violates object class restrictions.
notAllowedOnNonLeaf (66)
Indicates that the operation is inappropriately acting upon a
non-leaf entry.
notAllowedOnRDN (67)
Indicates that the operation is inappropriately attempting to
remove a value which forms the entry's relative distinguished
name.
entryAlreadyExists (68)
Indicates that the request cannot be fulfilled (added, moved,
or renamed) as the target entry already exists.
Sermersheim Internet-Draft - Expires April 2006 Page 49
Lightweight Directory Access Protocol Version 3
objectClassModsProhibited (69)
Indicates that an attempt to modify the object class(es) of
an entry's 'objectClass' attribute is prohibited.
For example, this code is returned when a client attempts to
modify the structural object class of an entry.
affectsMultipleDSAs (71)
Indicates that the operation cannot be performed as it would
affect multiple servers (DSAs).
other (80)
Indicates the server has encountered an internal error.
Sermersheim Internet-Draft - Expires April 2006 Page 50
Lightweight Directory Access Protocol Version 3
Appendix B. Complete ASN.1 Definition
This appendix is normative.
Lightweight-Directory-Access-Protocol-V3 {1 3 6 1 1 <IANA-
ASSIGNED-DIRECTORY-NUMBER>}
-- Copyright (C) The Internet Society (2005). This version of
-- this ASN.1 module is part of RFC XXXX; see the RFC itself
-- for full legal notices.
DEFINITIONS
IMPLICIT TAGS
EXTENSIBILITY IMPLIED ::=
BEGIN
LDAPMessage ::= SEQUENCE {
messageID MessageID,
protocolOp CHOICE {
bindRequest BindRequest,
bindResponse BindResponse,
unbindRequest UnbindRequest,
searchRequest SearchRequest,
searchResEntry SearchResultEntry,
searchResDone SearchResultDone,
searchResRef SearchResultReference,
modifyRequest ModifyRequest,
modifyResponse ModifyResponse,
addRequest AddRequest,
addResponse AddResponse,
delRequest DelRequest,
delResponse DelResponse,
modDNRequest ModifyDNRequest,
modDNResponse ModifyDNResponse,
compareRequest CompareRequest,
compareResponse CompareResponse,
abandonRequest AbandonRequest,
extendedReq ExtendedRequest,
extendedResp ExtendedResponse,
...,
intermediateResponse IntermediateResponse },
controls [0] Controls OPTIONAL }
MessageID ::= INTEGER (0 .. maxInt)
maxInt INTEGER ::= 2147483647 -- (2^^31 - 1) --
LDAPString ::= OCTET STRING -- UTF-8 encoded,
-- [ISO10646] characters
LDAPOID ::= OCTET STRING -- Constrained to <numericoid> [Models]
LDAPDN ::= LDAPString -- Constrained to <distinguishedName>
-- [LDAPDN]
Sermersheim Internet-Draft - Expires April 2006 Page 51
Lightweight Directory Access Protocol Version 3
RelativeLDAPDN ::= LDAPString -- Constrained to <name-component>
-- [LDAPDN]
AttributeDescription ::= LDAPString
-- Constrained to <attributedescription>
-- [Models]
AttributeValue ::= OCTET STRING
AttributeValueAssertion ::= SEQUENCE {
attributeDesc AttributeDescription,
assertionValue AssertionValue }
AssertionValue ::= OCTET STRING
PartialAttribute ::= SEQUENCE {
type AttributeDescription,
vals SET OF value AttributeValue }
Attribute ::= PartialAttribute(WITH COMPONENTS {
...,
vals (SIZE(1..MAX))})
MatchingRuleId ::= LDAPString
Sermersheim Internet-Draft - Expires April 2006 Page 52
Lightweight Directory Access Protocol Version 3
LDAPResult ::= SEQUENCE {
resultCode ENUMERATED {
success (0),
operationsError (1),
protocolError (2),
timeLimitExceeded (3),
sizeLimitExceeded (4),
compareFalse (5),
compareTrue (6),
authMethodNotSupported (7),
strongerAuthRequired (8),
-- 9 reserved --
referral (10),
adminLimitExceeded (11),
unavailableCriticalExtension (12),
confidentialityRequired (13),
saslBindInProgress (14),
noSuchAttribute (16),
undefinedAttributeType (17),
inappropriateMatching (18),
constraintViolation (19),
attributeOrValueExists (20),
invalidAttributeSyntax (21),
-- 22-31 unused --
noSuchObject (32),
aliasProblem (33),
invalidDNSyntax (34),
-- 35 reserved for undefined isLeaf --
aliasDereferencingProblem (36),
-- 37-47 unused --
inappropriateAuthentication (48),
invalidCredentials (49),
insufficientAccessRights (50),
busy (51),
unavailable (52),
unwillingToPerform (53),
loopDetect (54),
-- 55-63 unused --
namingViolation (64),
objectClassViolation (65),
notAllowedOnNonLeaf (66),
notAllowedOnRDN (67),
entryAlreadyExists (68),
objectClassModsProhibited (69),
-- 70 reserved for CLDAP --
affectsMultipleDSAs (71),
-- 72-79 unused --
other (80),
... },
matchedDN LDAPDN,
diagnosticMessage LDAPString,
referral [3] Referral OPTIONAL }
Referral ::= SEQUENCE SIZE (1..MAX) OF uri URI
Sermersheim Internet-Draft - Expires April 2006 Page 53
Lightweight Directory Access Protocol Version 3
URI ::= LDAPString -- limited to characters permitted in
-- URIs
Controls ::= SEQUENCE OF control Control
Control ::= SEQUENCE {
controlType LDAPOID,
criticality BOOLEAN DEFAULT FALSE,
controlValue OCTET STRING OPTIONAL }
BindRequest ::= [APPLICATION 0] SEQUENCE {
version INTEGER (1 .. 127),
name LDAPDN,
authentication AuthenticationChoice }
AuthenticationChoice ::= CHOICE {
simple [0] OCTET STRING,
-- 1 and 2 reserved
sasl [3] SaslCredentials,
... }
SaslCredentials ::= SEQUENCE {
mechanism LDAPString,
credentials OCTET STRING OPTIONAL }
BindResponse ::= [APPLICATION 1] SEQUENCE {
COMPONENTS OF LDAPResult,
serverSaslCreds [7] OCTET STRING OPTIONAL }
UnbindRequest ::= [APPLICATION 2] NULL
SearchRequest ::= [APPLICATION 3] SEQUENCE {
baseObject LDAPDN,
scope ENUMERATED {
baseObject (0),
singleLevel (1),
wholeSubtree (2),
... },
derefAliases ENUMERATED {
neverDerefAliases (0),
derefInSearching (1),
derefFindingBaseObj (2),
derefAlways (3) },
sizeLimit INTEGER (0 .. maxInt),
timeLimit INTEGER (0 .. maxInt),
typesOnly BOOLEAN,
filter Filter,
attributes AttributeSelection }
AttributeSelection ::= SEQUENCE OF selector LDAPString
-- The LDAPString is constrained to
-- <attributeSelector> in Section 4.5.1.7
Sermersheim Internet-Draft - Expires April 2006 Page 54
Lightweight Directory Access Protocol Version 3
Filter ::= CHOICE {
and [0] SET SIZE (1..MAX) OF filter Filter,
or [1] SET SIZE (1..MAX) OF filter Filter,
not [2] Filter,
equalityMatch [3] AttributeValueAssertion,
substrings [4] SubstringFilter,
greaterOrEqual [5] AttributeValueAssertion,
lessOrEqual [6] AttributeValueAssertion,
present [7] AttributeDescription,
approxMatch [8] AttributeValueAssertion,
extensibleMatch [9] MatchingRuleAssertion,
... }
SubstringFilter ::= SEQUENCE {
type AttributeDescription,
substrings SEQUENCE SIZE (1..MAX) OF substring CHOICE {
initial [0] AssertionValue, -- can occur at most once
any [1] AssertionValue,
final [2] AssertionValue } -- can occur at most once
}
MatchingRuleAssertion ::= SEQUENCE {
matchingRule [1] MatchingRuleId OPTIONAL,
type [2] AttributeDescription OPTIONAL,
matchValue [3] AssertionValue,
dnAttributes [4] BOOLEAN DEFAULT FALSE }
SearchResultEntry ::= [APPLICATION 4] SEQUENCE {
objectName LDAPDN,
attributes PartialAttributeList }
PartialAttributeList ::= SEQUENCE OF
partialAttribute PartialAttribute
SearchResultReference ::= [APPLICATION 19] SEQUENCE
SIZE (1..MAX) OF uri URI
SearchResultDone ::= [APPLICATION 5] LDAPResult
ModifyRequest ::= [APPLICATION 6] SEQUENCE {
object LDAPDN,
changes SEQUENCE OF change SEQUENCE {
operation ENUMERATED {
add (0),
delete (1),
replace (2),
... },
modification PartialAttribute } }
ModifyResponse ::= [APPLICATION 7] LDAPResult
AddRequest ::= [APPLICATION 8] SEQUENCE {
entry LDAPDN,
attributes AttributeList }
Sermersheim Internet-Draft - Expires April 2006 Page 55
Lightweight Directory Access Protocol Version 3
AttributeList ::= SEQUENCE OF attribute Attribute
AddResponse ::= [APPLICATION 9] LDAPResult
DelRequest ::= [APPLICATION 10] LDAPDN
DelResponse ::= [APPLICATION 11] LDAPResult
ModifyDNRequest ::= [APPLICATION 12] SEQUENCE {
entry LDAPDN,
newrdn RelativeLDAPDN,
deleteoldrdn BOOLEAN,
newSuperior [0] LDAPDN OPTIONAL }
ModifyDNResponse ::= [APPLICATION 13] LDAPResult
CompareRequest ::= [APPLICATION 14] SEQUENCE {
entry LDAPDN,
ava AttributeValueAssertion }
CompareResponse ::= [APPLICATION 15] LDAPResult
AbandonRequest ::= [APPLICATION 16] MessageID
ExtendedRequest ::= [APPLICATION 23] SEQUENCE {
requestName [0] LDAPOID,
requestValue [1] OCTET STRING OPTIONAL }
ExtendedResponse ::= [APPLICATION 24] SEQUENCE {
COMPONENTS OF LDAPResult,
responseName [10] LDAPOID OPTIONAL,
responseValue [11] OCTET STRING OPTIONAL }
IntermediateResponse ::= [APPLICATION 25] SEQUENCE {
responseName [0] LDAPOID OPTIONAL,
responseValue [1] OCTET STRING OPTIONAL }
END
Sermersheim Internet-Draft - Expires April 2006 Page 56
Lightweight Directory Access Protocol Version 3
Appendix C. Changes
This appendix is non-normative.
This appendix summarizes substantive changes made to RFC 2251, RFC
2830, and RFC 3771.
C.1. Changes made to RFC 2251:
This section summarizes the substantive changes made to Sections 1,
2, 3.1, and 4 through the remainder of RFC 2251. Readers should
consult [Models] and [AuthMeth] for summaries of changes to other
sections.
C.1.1. Section 1 (Status of this Memo)
- Removed IESG note. Post publication of RFC 2251, mandatory LDAP
authentication mechanisms have been standardized which are
sufficient to remove this note. See [AuthMeth] for authentication
mechanisms.
C.1.2. Section 3.1 (Protocol Model) and others
- Removed notes giving history between LDAP v1, v2 and v3. Instead,
added sufficient language so that this document can stand on its
own.
C.1.3. Section 4 (Elements of Protocol)
- Clarified where the extensibility features of ASN.1 apply to the
protocol. This change affected various ASN.1 types by the
inclusion of ellipses (...) to certain elements.
- Removed the requirement that servers which implement version 3 or
later MUST provide the 'supportedLDAPVersion' attribute. This
statement provided no interoperability advantages.
C.1.4. Section 4.1.1 (Message Envelope)
- There was a mandatory requirement for the server to return a
Notice of Disconnection and drop the transport connection when a
PDU is malformed in a certain way. This has been updated such that
the server SHOULD return the Notice of Disconnection, and MUST
terminate the LDAP Session.
C.1.5. Section 4.1.1.1 (Message ID)
- Required that the messageID of requests MUST be non-zero as the
zero is reserved for Notice of Disconnection.
Sermersheim Internet-Draft - Expires April 2006 Page 57
Lightweight Directory Access Protocol Version 3
- Specified when it is and isn't appropriate to return an already
used message id. RFC 2251 accidentally imposed synchronous server
behavior in its wording of this.
C.1.6. Section 4.1.2 (String Types)
- Stated that LDAPOID is constrained to <numericoid> from [Models].
C.1.7. Section 4.1.5.1 (Binary Option) and others
- Removed the Binary Option from the specification. There are
numerous interoperability problems associated with this method of
alternate attribute type encoding. Work to specify a suitable
replacement is ongoing.
C.1.8. Section 4.1.8 (Attribute)
- Combined the definitions of PartialAttribute and Attribute here,
and defined Attribute in terms of PartialAttribute.
C.1.9. Section 4.1.10 (Result Message)
- Renamed "errorMessage" to "diagnosticMessage" as it is allowed to
be sent for non-error results.
- Moved some language into Appendix A, and refer the reader there.
- Allowed matchedDN to be present for other result codes than those
listed in RFC 2251.
- renamed the code "strongAuthRequired" to "strongerAuthRequired" to
clarify that this code may often be returned to indicate that a
stronger authentication is needed to perform a given operation.
C.1.10. Section 4.1.11 (Referral)
- Defined referrals in terms of URIs rather than URLs.
- Removed the requirement that all referral URIs MUST be equally
capable of progressing the operation. The statement was ambiguous
and provided no instructions on how to carry it out.
- Added the requirement that clients MUST NOT loop between servers.
- Clarified the instructions for using LDAPURLs in referrals, and in
doing so added a recommendation that the scope part be present.
- Removed imperatives which required clients to use URLs in specific
ways to progress an operation. These did nothing for
interoperability.
C.1.11. Section 4.1.12 (Controls)
- Specified how control values defined in terms of ASN.1 are to be
encoded.
Sermersheim Internet-Draft - Expires April 2006 Page 58
Lightweight Directory Access Protocol Version 3
- Noted that the criticality field is only applied to request
messages (except UnbindRequest), and must be ignored when present
on response messages and UnbindRequest.
- Specified that non-critical controls may be ignored at the
server's discretion. There was confusion in the original wording
which led some to believe that recognized controls may not be
ignored as long as they were associated with a proper request.
- Added language regarding combinations of controls and the ordering
of controls on a message.
- Specified that when the semantics of the combination of controls
is undefined or unknown, it results in a protocolError.
- Changed "The server MUST be prepared" to "Implementations MUST be
prepared" in the eighth paragraph to reflect that both client and
server implementations must be able to handle this (as both parse
controls).
C.1.12. Section 4.2 (Bind Operation)
- Mandated that servers return protocolError when the version is not
supported.
- Disambiguated behavior when the simple authentication is used, the
name is empty and the password is non-empty.
- Required servers to not dereference aliases for Bind. This was
added for consistency with other operations and to help ensure
data consistency.
- Required that textual passwords be transferred as UTF-8 encoded
Unicode, and added recommendations on string preparation. This was
to help ensure interoperability of passwords being sent from
different clients.
C.1.13. Section 4.2.1 (Sequencing of the Bind Request)
- This section was largely reorganized for readability and language
was added to clarify the authentication state of failed and
abandoned Bind operations.
- Removed: "If a SASL transfer encryption or integrity mechanism has
been negotiated, that mechanism does not support the changing of
credentials from one identity to another, then the client MUST
instead establish a new connection."
If there are dependencies between multiple negotiations of a
particular SASL mechanism, the technical specification for that
SASL mechanism details how applications are to deal with them.
LDAP should not require any special handling.
- Dropped MUST imperative in paragraph 3 to align with [Keywords].
- Mandated that clients not send non-Bind operations while a Bind is
in progress, and suggested that servers not process them if they
are received. This is needed to ensure proper sequencing of the
Bind in relationship to other operations.
Sermersheim Internet-Draft - Expires April 2006 Page 59
Lightweight Directory Access Protocol Version 3
C.1.14. Section 4.2.3 (Bind Response)
- Moved most error-related text to Appendix A, and added text
regarding certain errors used in conjunction with the Bind
operation.
- Prohibited the server from specifying serverSaslCreds when not
appropriate.
C.1.15. Section 4.3 (Unbind Operation)
- Specified that both peers are to cease transmission and terminate
the LDAP session for the Unbind operation.
C.1.16. Section 4.4 (Unsolicited Notification)
- Added instructions for future specifications of Unsolicited
Notifications.
C.1.17. Section 4.5.1 (Search Request)
- SearchRequest attributes is now defined as an AttributeSelection
type rather than AttributeDescriptionList, and an ABNF is
provided.
- SearchRequest attributes may contain duplicate attribute
descriptions. This was previously prohibited. Now servers are
instructed to ignore subsequent names when they are duplicated.
This was relaxed in order to allow different short names and also
OIDs to be requested for an attribute.
- The present search filter now evaluates to Undefined when the
specified attribute is not known to the server. It used to
evaluate to FALSE, which caused behavior inconsistent with what
most would expect, especially when the not operator was used.
- The Filter choice SubstringFilter substrings type is now defined
with a lower bound of 1.
- The SubstringFilter substrings 'initial, 'any', and 'final' types
are now AssertionValue rather than LDAPString. Also, added
imperatives stating that 'initial' (if present) must be listed
first, and 'final' (if present) must be listed last.
- Disambiguated the semantics of the derefAliases choices. There was
question as to whether derefInSearching applied to the base object
in a wholeSubtree Search.
- Added instructions for equalityMatch, substrings, greaterOrEqual,
lessOrEqual, and approxMatch.
C.1.18. Section 4.5.2 (Search Result)
- Recommended that servers not use attribute short names when it
knows they are ambiguous or may cause interoperability problems.
- Removed all mention of ExtendedResponse due to lack of
implementation.
Sermersheim Internet-Draft - Expires April 2006 Page 60
Lightweight Directory Access Protocol Version 3
C.1.19. Section 4.5.3 (Continuation References in the Search Result)
- Made changes similar to those made to Section 4.1.11.
C.1.20. Section 4.5.3.1 (Example)
- Fixed examples to adhere to changes made to Section 4.5.3.
C.1.21. Section 4.6 (Modify Operation)
- Replaced AttributeTypeAndValues with Attribute as they are
equivalent.
- Specified the types of modification changes which might
temporarily violate schema. Some readers were under the impression
that any temporary schema violation was allowed.
C.1.22. Section 4.7 (Add Operation)
- Aligned Add operation with X.511 in that the attributes of the RDN
are used in conjunction with the listed attributes to create the
entry. Previously, Add required that the distinguished values be
present in the listed attributes.
- Removed requirement that the objectClass attribute MUST be
specified as some DSE types do not require this attribute.
Instead, generic wording was added, requiring the added entry to
adhere to the data model.
- Removed recommendation regarding placement of objects. This is
covered in the data model document.
C.1.23. Section 4.9 (Modify DN Operation)
- Required servers to not dereference aliases for Modify DN. This
was added for consistency with other operations and to help ensure
data consistency.
- Allow Modify DN to fail when moving between naming contexts.
- Specified what happens when the attributes of the newrdn are not
present on the entry.
C.1.24. Section 4.10 (Compare Operation)
- Specified that compareFalse means that the Compare took place and
the result is false. There was confusion which lead people to
believe that an Undefined match resulted in compareFalse.
- Required servers to not dereference aliases for Compare. This was
added for consistency with other operations and to help ensure
data consistency.
Sermersheim Internet-Draft - Expires April 2006 Page 61
Lightweight Directory Access Protocol Version 3
C.1.25. Section 4.11 (Abandon Operation)
- Explained that since Abandon returns no response, clients should
not use it if they need to know the outcome.
- Specified that Abandon and Unbind cannot be abandoned.
C.1.26. Section 4.12 (Extended Operation)
- Specified how values of Extended operations defined in terms of
ASN.1 are to be encoded.
- Added instructions on what Extended operation specifications
consist of.
- Added a recommendation that servers advertise supported Extended
operations.
C.1.27. Section 5.2 (Transfer Protocols)
- Moved referral-specific instructions into referral-related
sections.
C.1.28. Section 7 (Security Considerations)
- Reworded notes regarding SASL not protecting certain aspects of
the LDAP Bind messages.
- Noted that Servers are encouraged to prevent directory
modifications by clients that have authenticated anonymously
[AuthMeth].
- Added a note regarding the possibility of changes to security
factors (authentication, authorization, data confidentiality).
- Warned against following referrals that may have been injected in
the data stream.
- Noted that servers should protect information equally, whether in
an error condition or not, and mentioned specifically; matchedDN,
diagnosticMessage, and resultCodes.
- Added a note regarding malformed and long encodings.
C.1.29. Appendix A (Complete ASN.1 Definition)
- Added "EXTENSIBILITY IMPLIED" to ASN.1 definition.
- Removed AttributeType. It is not used.
C.2. Changes made to RFC 2830:
This section summarizes the substantive changes made to Sections of
RFC 2830. Readers should consult [AuthMeth] for summaries of changes
to other sections.
Sermersheim Internet-Draft - Expires April 2006 Page 62
Lightweight Directory Access Protocol Version 3
C.2.1. Section 2.3 (Response other than "success")
- Removed wording indicating that referrals can be returned from
StartTLS.
- Removed requirement that only a narrow set of result codes can be
returned. Some result codes are required in certain scenarios, but
any other may be returned if appropriate.
- Removed requirement that the ExtendedResponse.responseName MUST be
present. There are circumstances where this is impossible, and
requiring this is at odds with language in Section 4.12.
C.2.1. Section 4 (Closing a TLS Connection)
- Reworded most of this section to align with definitions of the
LDAP protocol layers.
- Removed instructions on abrupt closure as this is covered in other
areas of the document (specifically, Section 5.3)
C.3. Changes made to RFC 3771:
- Rewrote to fit into this document. In general, semantics were
preserved. Supporting and background language seen as redundant
due to its presence in this document was omitted.
- Specified that Intermediate responses to a request may be of
different types, and one of the response types may be specified to
have no response value.
Sermersheim Internet-Draft - Expires April 2006 Page 63
Lightweight Directory Access Protocol Version 3
Intellectual Property Statement
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at ietf-
[email protected].
Disclaimer of Validity
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Copyright Statement
Copyright (C) The Internet Society (2005).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Sermersheim Internet-Draft - Expires April 2006 Page 64
|
